D link dir 320 connection to a computer. Old horse, does not spoil the furrow

This manual shows and explains in detail how to set up wifi router D-Link DIR-320 for Beeline and Rostelecom Internet.

Let's take a look at the following points step by step:

  • How to connect DIR-320 to Internet line and computer for setup
  • How to set up an L2TP connection for Beeline Internet and PPPoE for Rostelecom
  • How to set up a Wi-Fi password and name wireless network
  • Setting up IPTV television (Digital TV Beeline and Rostelecom).

So, everything you may need to configure this wireless router is here, you just have to read carefully.

How to connect a router

I'll start with how to properly connect a Wi-Fi router to configure it, since even here there are problems.

Behind the D-Link DIR-320, apart from power and a couple of buttons, there are five ports: 4 LAN and 1 Internet. It is to the last connector that you need to connect the cable of your Internet provider.

I also note that the setup itself will be easier if you perform it from the computer that is connected to the router by wires: connect one of the LAN ports on the device with a connector network card on the computer.

And the last two points:

  • When setting up, the Beeline, Rostelecom or High-Speed ​​Connection connection on the computer must be disconnected. And after you set it up, don't run it either - the router itself will connect to the Internet.
  • If you are unable to enter the router settings, as described below,.

So, now you can proceed to the configuration itself.

Login to the settings web interface

To enter the D-Link DIR-320 settings, launch a browser and enter 192.168.0.1 in the address bar, you should see a login and password request. Standard login and password, if you have not changed them before - admin(if the password is not suitable, then you will be “thrown” again to the password entry page. It may have been changed. Then you can reset the router to factory settings by pressing and holding the Reset button for 15-20 seconds).

After entering correctly, you will be on home page with basic device information. Click "Advanced Settings" at the bottom of the page.

Setting up D-Link DIR-320 for Beeline

To configure the connection, in the "Network" item, select "WAN", a list of connections will open. At the bottom of the list, click "Add" and set following options Internet connection Beeline:

  • Connection type - L2TP + Dynamic IP
  • Login, password - your Internet login data that you received from Beeline
  • VPN server address - tp.internet.beeline.ru

The rest of the settings do not need to be changed. Click "Save", after which the page with the list of connections will open again, and at the top there will be a notification with a one, click on it and click "Save".

Now, if you refresh the page, you should see that the newly created connection is in the Connected state, which means that the Internet is configured correctly and you can go to Wi-Fi setup networks. Do not forget, the Beeline connection on the computer must be terminated.

On the advanced settings page, in the "Network" item, click "WAN". A list of connections will open, where there will be only one - click on it, and on the next page click "Delete". You'll be back to already empty list connections. Click "Add" and enter the following parameters for the Internet from Rostelecom:

  • Connection type - PPPoE
  • Username and password - Internet login data provided to you by Rostelecom

The remaining parameters can be left unchanged, click "Save". You will return to the list of connections. Please note that the "light bulb" is on at the top of the DIR-320 settings page, click on it and select "Save".

Refresh the page after a minute. If you see that the connection status has changed to “Connected”, then you did everything right and the Internet is already there, you can proceed to setting up Wi-Fi. Let me remind you that the connection of Rostelecom on the computer itself should be disabled.

Setting up a Wi-Fi network

In order to configure the wireless Wi-Fi network settings on the DIR-320, on the page with advanced settings in the Wi-Fi item, click "Basic Settings", on the page that appears, you can set your wireless network name (SSID) instead of the standard DIR-320.

Then save these settings and return to the "Wi-Fi" item, now you should select "Security Settings". This is where the Wi-Fi password is set. Recommended settings:

  • Network Authentication - WPA2-PSK
  • Encryption key PSK (password) - at least 8 characters, without Russian letters.

Save the settings, do not forget to also click "Save" at the top of the change indicator (light bulb). In general, the DIR-320 setup is complete.

TV setup

In order to customize digital television Beeline or Rostelecom, on the main page of the router settings, select "Master IPTV settings”, in it, specify the port where the set-top box will be connected and save the settings. Connect the set-top box to the selected LAN port.

The Internet is an integral part of the modern lifestyle. You can enter the digital web through mobile applications and Wi-Fi waves. But the reception quality and signal level directly depend on the transmitting device, in our case, the router. D-link models are the most popular for consumer demand. The most important aspect when creating an outlet to the internet space is correct setting D-Link DIR 320.

Creating a connection between the router and the computer

In order for the D-Link Deer 320 to reliably perform all tasks, it will need to be installed correctly. Usually supplied with detailed instructions, but not in all cases. Before proceeding to the implementation of the connection with the computer, you need to check its characteristics:

  1. Open the terminal control panel.
  2. Click on "Network Status".
  3. Go to the page for changing properties.
  4. In the new menu, open the properties of the local grid.
  5. A list of radio buttons will appear. Define "TCP/IPv4 protocol".
  6. In the menu that appears, allow the determination of the IP number and DNS server in automatic mode.
  7. Save.

The connection is made using the wires supplied with the device. Among them: a cable and a five-volt power supply, LAN cable. The router has seven functional connectors (for power, USB - input, network jack, LAN - jacks). Connect the cable supplied by the service provider to the INTERNET jack. Connect the wire supplied with the router to the LAN jack on the PC, and the other end to the router (this scheme is typical for a PC without WiFi adapter). If you distribute traffic via Wi-Fi waves, there is no need to use a LAN wire. Plug the power supply into an outlet.

Video on setting up a D-Link router:

Next, to log in to the Wi-Fi router, you need to launch any standard browser and enter the numbers 192.168.0.1 in the search bar. A menu will open where you will need to go through authorization (enter your login and pin code). When using the router for the first time, this information is standard, name and pin code- "admin". But if Account is already there and you forgot the combination of numbers, click on the "Reset" restart on the back.

Cable connection

There are several types of communication:

  • PPTP
  • PPPoE;
  • L2TP.

All manipulations are performed in the device service. To adjust PPTP you will need:

  1. Open the menu, configure the router, select the "Wan" item.
  2. On the next page, click on the add button.
  3. Assign the "PPTP dynamic IP" method.
  4. Check the box for automatic connection in the VPN section.
  5. Specify the user's personal information (login, pin and confirmation), mark VPN properties. All this information is provided by the provider company that connects to the Internet. The client's data is entered into a bilateral agreement with the provider. If they are missing, contact support.
  6. Apply.
  7. Go to the system properties of the interface and click on the "save and exit" button. The new changes will take effect.

Debugging L2TP parameters:

  1. In the front window, under the "Network" tab, find the value "Wan".
  2. In the next menu, click on the Add radio button.
  3. Set the type to "L2TP dynamic IP".
  4. Put a cross for automatic detection.
  5. Fit confidential information owner (nickname, code combination and confirmation), specify the address of the VPN server.
  6. Go to system partition interface and click on the save panel. The new settings will take effect.

The procedure for adjusting the PPPoE connection is identical to the above methods. The only difference is in the protocol. But there are also PPPoE, L2TP, PPTP protocols with a static IP address. The debugging order is identical for all protocols and consists of the following steps:

  1. On the working field, under the "Network" tab, select the "Wan" item.
  2. Confirm the addition in the window that appears.
  3. Select the format "L2TP, PPPoE, PPTP Static IP".
  4. In the identifier parameters section, enter the IP address, DNS server, default gateway, netmask.
  5. Specify user data (login, security code and code repetition).
  6. Go to system parameters interface and save and reload. The new settings will take effect.

Video on setting up a PPPoE connection on a D-Link router:

Typically, services with static protocols D-LINK setup DIR 320 provided legal entities and companies, or individuals on special request.

Access to the network via a USB modem

There is a USB socket on the back panel. The router can work with mobile internet. Such modems are produced by almost every telecom operator (beeline, mts, megaphone). To establish communication with an external adapter. It is required to go to the properties, in the interface of the router. Set value USB adapter in the first section. Write the name of the carrier. If it is not in the default list, select the "custom" option. Fill in all the required fields with personal characteristics (username and code), ask your provider or telecom operator for them.

Video to help you set up the router step by step:

Go to the "USB modem" tab, go to the information section. In the window that opens, check the modem device type and generation wireless communication(4G, 3G, E). Allow joining mobile network Internet. Click on the action button. Some modem devices use a default password when logging in. To avoid constantly entering a password when you turn it on, go to the "Pin" tab in USB section. Enter the code provided by the provider.

Wireless connection

To change the characteristics of Wi-Fi, you need to go to the "network" tab and select the " wireless transmission". In this window, the user can stop the wireless method of traffic transmission. Specify the network authentication method.

Factory settings are not designed to encrypt information. To protect traffic from interception, specify a method other than "Open". Come up with a PSK code - this is the password that will be requested when a Wi-Fi network is found.

Software update

It is recommended to constantly monitor the emergence of new updates and install them. Each update adds new features to the router and raises the level network protection from unwanted hacking. In the "Support" tab you can find the latest current version of the software.

To update the device software, you need to go to the "system" section and open the "update" section there. software". A window will appear in which you need to click the "Browse" button. Specify the path to the current firmware file that is on your computer (downloaded in advance from the Internet resource).

Establishing a Wi-Fi Connection

When all the required settings have been made, the final stage of setup begins. On PC with operating system Windows 7 order is as follows:

  1. On the right side of the taskbar is the "internet access" icon. Click on it.
  2. A window will open showing all nearby wireless Internet distributions. Click on the corresponding channel.
  3. Click on the "connection" icon.
  4. If a security code is set, you must enter it.

After completing these steps, the Internet will be available to you.

Conclusion

After performing the required debugging, the device will correctly perform all its functions. The process of configuring the router is quite laborious, not every user is able to handle it. Therefore, when drawing up an agreement with the provider, he provides a specialist technician who will set up the router for high-quality work.

The Dir-320 router, the brainchild of the popular D-link company, is a wireless router with a data transfer rate of 54 Mbps and USB 2.0 support.

Unfortunately, currently this model is no longer relevant, since the technical characteristics of the router - according to current requests - leave much to be desired.

Therefore, relatively recently - in 2011, the D-link company released an updated Dir-320 NRU with support for WiMAX, 3G GSM, CDMA and data transfer rates up to 150 Mbps - for 2011 this is enough good scores.

Brief overview of the dir 320 router

Detailed list specifications router is shown in the following illustrations:



The body of the router is made in black with one external antenna and on the right side of the router.

The indicator panel consists of 8 elements:

  • "Power" - power on/off;
  • "Internet" - if the indicator is blinking - traffic is being transmitted, if it is just "on" - the connection is established;
  • "Wireless network" - blinking - data is being transferred, "on" - the network is active;
  • "Local network 1-4" - blinking - traffic is being transmitted through the corresponding port, "on" - network device connected;
  • "USB" - "on" - external usb device connected, blinking – connection established.

The back panel of the dir 320 router:

  • "LAN 1-4" - ports for connecting network devices;
  • "Internet" - port for connection to "Ethernet line" or DSL modem;
  • "USB" - port for connecting usb-modems;
  • "5V-2A" - connector for connecting the power adapter;
  • "Reset" - a button that resets to factory settings.

How to set up an internet connection on a d link dir 320 router?

Prepare an agreement with the service provider in advance, as it will contain the authorization data required to set up an Internet connection.

To enter the router settings, you need to connect a router d link dir 320 To and in the address bar of the browser enter the address 192.168.0.1. When prompted for a username and password, enter "admin/admin".

If your router was previously in operation, then before making settings, you must reset its configuration to the factory settings using reset buttons. Otherwise, authorization errors may occur (for example, an incorrect username and password will be specified) and problems with setting up the device.

Below is appearance router interface d link dir 320 from software version "1-2-94", which is stock by default.

After the first login to the web interface, you need to change the administrator password (in order to protect the network from possible unauthorized access), and then click the "Save" button.

To create a new Internet connection, open the "Network" section, then "Connection", click the "Add" button and do the following:

  • "Name" - leave it unchanged;
  • "Connection type" - given parameter depends on the authorization data from the contract with the provider.

Choose one of the options:

PPPoE

  • in the "PPP Settings" block, enter the "Username" and "Password" (twice);
  • tick the options: "Keep Alive" - ​​connection support, "NAT" and "Firewall";
  • optionally, you can enable "PPP debugging" - the introduction of debugging records over the connection and "PPPoE forwarding".

IPoE

  • check the boxes "Obtain an IP address automatically" and "Obtain DNS address– servers automatically”;
  • "Vendor ID" - if required by the provider.

PPTP or L2TP

  • if you need the connection to be made automatically - select "Connect automatically";
  • "Service name" - enter the ip or url address of the authentication server;
  • enter "Username" and "Password";
  • in the "Encryption" line, select one of the options: "Off", "MPPE 40/128 bit", "MPPE 40 bit" or "MPPE 128 bit".

3G

  • in the line "Mode" select - "Auto";
  • authorization data is filled in by analogy with the above;
  • "APN" - access point name;
  • "Dial number" is the number to connect to the operator's authorization server.

Setting up wifi on a d link dir 320 router

To set up a wireless network, select " General settings” and click “Turn on wireless connection”.

  • specify in the line "SSID" the name of the network being created;
  • "Country" and " Wireless mode" - without changes;
  • in the line "Channel" - select either "Auto" or from 1 to 13;
  • if you plan to limit the number of connections to the network - indicate the desired number in the line " Maximum amount clients."

Then open Security Settings.

Select one of the options in the "Network Authentication" line:

A). "Open", "Shared", or "WEPAUTO"

b). "Open-IEEE8021X"

c) "WPA-PSK", "WPA2-PSK" or "WPA-PSK/WPA2-PSK mixed"

Depending on your selection, enter the security key you will need for the next wifi connections devices to the wireless network.

Setting up IPTV

Please note that the "IPTV" section is present only in software versions "1_3_3" and "1_4_0".

Settings are being made in the "IPTV Setup Wizard" menu

Here you only need to select the port number to which the set-top box is connected.

  • click "Add";
  • "Type" - for "IPTV" select "Transparent";
  • "VLAN ID" if required by the provider;
  • in the "Port" line, select the number of the port to which the set-top box is connected.

To complete the settings of the d link dir 320 router, click "Save changes".

In version "1-2-94" there is no section "IPTV Setup Wizard". In the "Advanced" menu, check if "IGMP" is enabled:

Additional features of the d link dir 320 router

As advanced settings you should pay attention to "WMM" (Wi-Fi Multimedia). In short, it is a protocol for prioritizing voice traffic (AC_VO), video traffic (AC_V), traffic from devices without a QoS mechanism (AC_BE), and traffic without latency and performance requirements (AC_BK) over normal traffic passing through wireless network.

  • "Aifsn" (variable frame interval ratio): the smaller the value, the higher the priority;
  • "CWMin/CWMax" (minimum and maximum size concurrent access windows);
  • "Txop" (data transfer capability);
  • "ACM" (mandatory access control);
  • "Ack" (receipt confirmation).

There is no big difference in the external component of the "web interface" between versions "1_2_94" and "1_3_3".

However, starting from version “1_4_0”, the router interface is more similar to: the main elements can be found in the following illustrations:





Setting up your router is easy. How to do it step by step, we will consider in this article. And so let's get started.

Connecting to a computer

  • Turn off your PC.
  • Using a cable, connect the computer to the router in one of the LAN ports.

  • To establish a 3G GSM, WiMAX or CDMA connection, connect a USB modem to the port on the side of the router.
  • Plug the power supply into the router's power socket and then into a power outlet.

  • On the router, press the ON/OFF button to turn on the device.
  • Turn on the PC.
  • Then set up your computer to obtain IP addresses automatically (DHCP).

Configuring the D-link dir-320 router

Connecting to the web interface

It is convenient to make settings through the web interface of the router. Let's do it as the instructions say.

  • Launch the browser and enter 192.168.0.1 in the line.
  • Enter the username and password - admin.

  • Press Enter to login.

After successfully entering the web interface, the language can be changed to a more convenient one.


Changing the base password

The first step is to change the factory password to your secret phrase. This will help improve security.

  • In the web interface of the router, at the bottom right, find the Advanced settings link and follow it.

  • Then, in the System section, click on the Administrator password link.

  • Enter your password on the page and write it down.

  • Click Apply to save the new data.

Device setup


If the INTERNET LED on the front of the router is on, the installation was successful. Click Next.


PPPoE mode


  • Enter the name of the compound (1).
  • Enter your login (2).
  • Enter the password (3) and repeat it again (4) as shown in the figure. This data must be provided by the Internet access provider.

  • Click Next and then Apply.

PPPoE access setup completed.

Static IP

Click on Static IP


  • Specify the name of the connection (1).
  • Enter the IP address (2) and subnet mask (3).
  • Enter gateway IP (4), this connection, and the DNS server address (5), as the instructions say. This information is given by the provider when concluding an agreement on the provision of Internet services.

  • Apply.

The connection is ready.

Dynamic IP

Specify position Dynamic IP


  • Connection name (1).
  • Remove the flag (2).
  • Fill in the box Primary DNS server (3). This information must be provided by your ISP.
  • Apply.

Installation of Internet access via Dynamic IP is completed.

WIFI network setup and connection

Upon completion of filling in the necessary settings with the data, a window with the configuration will appear. wireless connection. Or it can also be configured manually. To install WIFI, follow the instructions below.

  • If we set it up manually, then we will go to the wifi network settings page.

  • Highlight the position Router.


Loading...
Top