For temperature monitoring of the main components of the computer and for adjusting the rotation speed of the processor cooler and other fans installed in the computer. But before you start using the program, you need to install the Russian language in the program and make settings for the program.
How to change language in SpeedFan
First, you need to configure the interface in SpeedFan and make it in Russian, and to do this, launch the program and close the additional window called Hint by clicking on the Close button. Then in the program window you need to click on the Configure button.
Program for increasing the speed of the SpeedFan cooler with an English interface
A window called Configure will open. In this window, you need to go to the Options tab.
SpeedFan crack on the Options tab On this tab, in the Language item, you need to select Russian from the pop-up list and click on the OK button located at the bottom of the program window. After this, the window called Configure will close, and the program interface will already be displayed in Russian.
How to set up the SpeedFan program
Now you need to configure SpeedFan correctly, and to do this, open the Configuration window again and go to the Options tab.
Recommended program settings On this tab, you can check the boxes Launch minimized and Minimize when closing, so that when you launch and close the program, it will immediately minimize and hide in the tray. You can also check the box next to Full fan speed on exit, since when you restart the computer, more energy is consumed and the computer heats up more. If you check the static icon box, then just the program icon will be displayed in the tray instead of the temperature readings from the sensors. By clicking on the OK button, all settings will be applied.
In SpeedFan how to change the fan speed
Using this program, you can adjust the fan speed in automatic or manual mode. In order for the program for adjusting the cooler speed to work in automatic mode, you must first set the minimum and maximum temperature conditions at which the fans will spin slowly or at full power.
SpeedFan fan speed setting Open the Configuration window and on the Speeds tab you will see how many fans and on which devices this program can regulate the fan speed. On this tab, click on the desired fan and at the bottom of the window, check the Auto Change box. Do this with those fans that you want to regulate.
Setting temperature conditions for fan operation Then we go to the Temperature tab and see that there are many sensors indicating temperature, but not all devices have fans installed. On this tab, click on the device for which you set Autochange on the Speed tab and at the bottom of the window set the temperature limits in the Desired and Alarm items. If the temperature is below the set Desired, the fans will spin slowly, and if the temperature is higher than the set Alarm, the fans will start spinning at full speed. Thus, set the temperature conditions for all the fans that you want to regulate, and when everything is ready, click OK and the configuration window will close.
In SpeedFan, the fan speed temperature controller operates in automatic mode For the specified parameters to start working, you need to check the box next to Auto fan speed in the program window.
Video
In this video called SpeedFan how to use the video explains how to change the rotation speed of the cooler depending on the temperature.
SpeedFan is one of the most popular free programs for monitoring the state of your computer with the ability to regulate fan speed. It is for the second part of its functionality that many users install this software on their computer, because it is much easier to configure the cooler directly in the operating system, without entering the BIOS. However, SpeedFan also succeeded in monitoring temperatures, voltage, and cooler rotation speeds. The user only needs to customize the software for himself in order to interact with it comfortably.
As part of today’s material, we want to discuss the complete configuration of the mentioned application, examining each important detail step by step. The entire process will be divided into separate sections, so you can familiarize yourself with the content and immediately proceed to perform the necessary actions. However, we still recommend that you learn about all the intricacies in order to discover new facets of editing parameters in SpeedFan.
Interface
It is always recommended first of all to customize the interface for yourself in order to simplify all further actions with the software. It’s worth noting right away that SpeedFan has localization into Russian, so choosing this particular language of buttons and functions will allow you to quickly understand all the components. The interface configuration is as follows:
Once the configuration is complete, be sure to apply the changes, otherwise all settings will be automatically reset to their original state.
Fan control
Next, let's look at the most interesting feature of SpeedFan - fan control, which is why many people install this software. First, pay attention to the main menu: here basic information about the state of components is displayed - temperature, speed of rotation. However, this is not what we need now. Check the box "Auto fan speed" so that the program automatically manages them as the system loads and temperatures increase. Just below are three lines responsible for the ability to quickly change the rotation speed.
Then go back to the window "Configuration" and open the tab "Fans". Here you can tick the items that will be monitored. As you can see, not all coolers present here are always actually installed in the computer, so a checkbox is not required. Enabling unnecessary parameters will only add a few unnecessary lines to the report or notification.
Next we will touch on the topic of speed control. This is done in the corresponding tab, where three items are marked - system, processor and an additionally connected cooler through the AUX sensor. Select one of the items so that two control values appear below. Here you can set the minimum and maximum rotation speed. Read more about changing these parameters in our other articles by clicking on the links below.
Additional fan control settings
There is another tab responsible for additional fan control settings. Here you add one of the devices and fine-tune the rotation speed distribution to specific temperatures. The procedure for creating a new profile looks like this:
- Move to the tab "Fan Control". Here, check the box next to "Advanced fan control" and click on "Add".
- Enter a name for the new controller.
- Select the new profile and in the pop-up list, identify the fan device connected to one of the connectors.
- Now add a device whose temperature will be detected. To do this, click on the bottom button "Add". As you can see from the screenshot below, the button "Add" a little hidden in the interface. This is due to errors in the development of windows and you will not be able to fix the problem yourself.
- From the list that opens, select the component whose temperature you want to monitor.
- Then modify the graph by moving the rotation speed points up or down depending on your needs. So you can make sure that from a temperature of 30 to 60 degrees the speed of revolutions will be at the same level, and then increase by the specified amount of percent.
Additional chip properties
In the tab "Additionally" There are several more properties that allow you to configure the temperature offset. To get acquainted with them, you will first need to select the chip itself by expanding the pop-up menu. It displays all connected devices.
Next, all that remains is to choose an interpretation and set two temperature offsets, if necessary. Just don't forget to press the button "OK" after each change is made so that they are saved.
Creating Events
Sometimes you want something to happen automatically when special events are achieved. To accomplish this task, SpeedFan allows you to create special scripts, completely customizing them yourself. Let's look at one example of writing such an event.
- Move to the tab "Events".
- In the popup menu "If" select the operator that is responsible for the condition, such as CPU temperature.
- Next, set a condition, for example, when the temperature exceeds or falls below a certain value.
- Specify the frequency of the event duration at which the condition will trigger.
- Set the condition itself, for example, displaying a notification, sending an email, or a sound signal.
- Set additional descriptions and actions if required.
- Click on the button "Add".
- One line will appear at the top with a detailed description of the condition.
Using exactly the same method, you can add several more different events that will perform some action when the goal is achieved. Such settings allow you to create flexible conditions, optimizing the operation of the software.
Sending messages by email
Above we mentioned sending messages via email. Now is the time to talk about setting up this process. The built-in functionality of the software in question allows you to enter your address and additional information, which will later be used to send reports on the operation of the system or certain warnings. The entire configuration is built completely individually and is carried out through the menu "Mail".
Making report
Reports in SpeedFan are generated automatically, but you will first need to enable their saving and configure some parameters. All data is entered into a separate file with all the required notes, and it is stored for a certain number of days or sent by mail. The report configuration looks like this:
Viewing Hard Drive Status
Finally, let's look at two important functions that have little to do with the topic of setting up the program, but have a place in this material. First, pay attention to the tab "S.M.A.R.T.". Here you can quickly check the status of the connected drive by running one of the available tests. You will be shown performance, physical condition and the values of key parameters.
Charts
The formation of graphs will allow for a more successful analysis of the system by adding the necessary indicators to the display. This includes: system temperature, CPU, graphics adapter and additional components. In addition, you can analyze not only degrees, but also voltage by selecting the appropriate mode.
Now you are familiar with the basic aspects of setting up the SpeedFan program. As you can see, there are really a lot of parameters here, and after familiarizing yourself with each of them, the procedure for mastering the software will take much less time, which will allow you to immediately use the tool to its full potential.
A fairly common problem for all fans of computer games and graphics editors: overheating of the processor, video card, and unstable operation of the cooler. To solve this “illness” a program called Speedfan was created. This simple utility will help you monitor the temperature of all components that may be subject to overheating, even the hard drive. In this article you will get to know the program better and learn how to use it.
Installing and downloading the program
The Speedfan program can be freely downloaded from the official website http://www.almico.com/speedfan.php
Go to the “Downloads” tab.
On this page you will see another section with the same name “Downloads”, and in it there is a small link with the latest version of the program. Click on it to start the download automatically.
The program installer takes up very little memory, so it downloads very quickly. Once you run it, you'll need a license agreement. Click on the “I Agree” button.
In the next tab, several items will appear, next to which you need to tick. This is adding shortcuts to the desktop, to the quick access panel. Click “Next”.
Select the program installation directory. If you have two disks, then do not install it on the local one, since it should be allocated for the required systems. You can select a folder using the “Browse” button. Click “Instal” to start the download.
The program will install in just a few seconds, you need to wait until the line at the top is filled with green.
At this point, the installation of the program is complete, you can begin setting up and working.
How to set up the Speedfan program
Now you can adjust the rotation speed of the fans in the cooler, control the temperature of the video card, hard drive, and central processor.
- Access the program via a shortcut on the desktop or in the Start panel.
- The entire utility interface is in English. You only need a little knowledge to easily understand all the components.
- All configuration takes place in the configuration section, click on the “Configure” button to enter it.
A new window will open in front of you, containing many tabs. First go to “Temperature”. Here you can configure the display of component temperatures. Check all of them, namely:
- GPU – your video card;
- HDD – hard drive of a computer or laptop;
- Temp – sensors on the motherboard;
- Core – CPU cores that must always be cooled.
All these parameters must have their own maximum temperature, upon reaching which the program will notify you and speed up the operation of the fans in the cooler. At the bottom of the window you can set values for each component separately.
Click on the component, enter the value in the “Warning” column below, if you know what the temperature limit for this component is. For example, for older video cards, heating above 93 degrees is not recommended.
By going to the “Speeds” tab, you can set your cooler speed values. This promotes better cooling, but wears them out more.
Now apply all the parameters by clicking “Ok”, exit and go to the “Charts” window. These are charts that are easy to view. Check the boxes that concern you most. This way you can track the metrics in the chart.
Now that everything is set up, you can simply go into the program and look at the temperature readings, follow the diagram, change the cooler speed at your discretion.
Please note that sometimes it is not practical to change the speed of rotation of the screw, as it will have to be lubricated more often. If you don’t know how to do this, then everything will become even more complicated, because the special rubber gasket inside the cooler will quickly wear out without lubrication, and as a result it will become unusable and begin to make loud sounds.
To prevent this from happening, do not set new values on old equipment. Coolers wear out relatively quickly, it is better to take care of them - pay attention to special cooling pads if you need to lower the temperature.
SpeedFan is a free program that allows you to change the fan speed and temperature in your PC system. You can either set a fixed speed or configure its dynamic changes depending on the temperature inside your computer case. We recommend that only advanced users learn to use SpeedFan; beginners can do a lot of mischief using the SpeedFan program.
How to use SpeedFan
To start using SpeedFan, you, of course, need to download and install it. It is recommended to use only trusted sites (for example, get the program here: http://www.softportal.com/software-3121-speedfan.html), otherwise you may receive a damaged version, catch a virus, a Trojan, or encounter several of these troubles at once: Dernaket.ru, Amigo Browser, omiga-plus.com, etc.
So, after downloading and installing, launch SpeedFan.
To begin with, if not selected Russian interface, it would be a good idea to switch to it for greater convenience of further work.
Russification is done very simply: click Configure(this is a button on the first main tab, which for now will be called in bourgeois language - “Readings”), among all the tabs we find Options, and there is already a point there Language. We select our native language, which is already built-in from the very beginning - no need to download any additional localization tools.
- These are cooler sensors detected by the SpeedFan program, they are designated as Fan.
- Here you can track the temperature of the processor (CPU or Temp), hard drive (HDD), video card (GPU).
- When using this zone, you can adjust the rotation speed of the coolers.
Let's move on to mastering the direct functions of the SpeedFan program
First tab "Indicators"(the same former “Readings”) will allow you to see the rotation speed of the fans, the temperature and how stressed the system is.
Second - "Frequencies". There you can overclock the processor and specify the conditions under which the system bus frequency will increase or decrease. Remember that overclocking the processor can be dangerous, even breaking your computer. But a little overclocking can be safe, and performance will increase significantly.
Using SpeedFan contributions "Information" And "SMART“, you can find out the status of the RAM and hard drive.
Then "Charts"— temperature graphs of computer devices are shown. There it is convenient to monitor under what circumstances the temperature rises or falls.
You need to start settings in the tab "Indicators" after going to it and pressing the button Configuration.
A menu with several tabs will open − Fans, Speeds, Voltages, Temperature etc. When you go to each of the tabs, a list will appear in which you need to check the boxes where you need to activate. There you can also edit any of the available parameters.
By changing certain values, we will adjust the reliability, stability, noiselessness and speed of the computer. Let's say, if you lower the fan speed without changing anything else, the result will be as follows: the computer will make less noise, but heat up more.
It would seem that “the nose is out and the tail is stuck,” but this is still not entirely true. By experimenting with the settings, it is quite possible to achieve more comfortable and high-quality computer operation (objectively or exclusively for you) than without using the program. But you should clearly understand all the characteristics of your equipment in order to obtain a similar result, guaranteed and safe for the system.
In the tab "Events" the program's actions are configured when a particular temperature is reached (for example, if the processor heats up to 75 degrees Celsius, immediately turn off the computer).
It makes sense to use SpeedFan only for advanced users; if you are not confident in your abilities, it is better to put the program aside for a while.
SpeedFan— бeсплaтнaя прoгрaммa, прeднaзнaчeннaя вo (избeжaниe упрaвлeния скoрoстями вeнтилятoрoв, a тaкжe для кoнтрoля зa тeмпeрaтурaми и нaпряжeниями в кoмпьютeрax с мaтeринскими плaтaми, имeющими aппaрaтныe дaтчики. Прoгрaммa тaкжe мoжeт oтoбрaжaть инфoрмaцию S.M.A.R.T. и тeмпeрaтуру жёсткoгo дискa, eсли дaннaя вoзмoжнoсть пoддeрживaeтся винчeстeрoм. Тaкжe имeются вoзмoжнoсти FSB changes for some components and support for SCSI drives. But the main feature of this program is that it can change fan speeds depending on the temperature. current temperatures (this method is not supported by all sensors). This reduces noise and energy consumption.
This guide is for any version of SpeedFan.
Setting up the program
Press the button " Configure».
Here we have the first tab – “ Temperatures", displaying the sensors installed on the motherboard and the current temperatures with standard parameters.
Let's start setting up
You can see that all available temperature values that the SpeedFan fog can detect are displayed. The “Chip” column indicates the sensor chip. In this case, you and I have three different chips: one W83782D and two LM75. We can tell the difference between the two LM75s because of their different addresses ($48 and $49). The LM75 chips, in this case, are essentially clones created by the W83782D, and we won’t pay much attention to them, because all temperatures are available directly through the W83782D. Yes, this is not always true. Winbond chips can be configured in such a way that they will actually bury (save) the real temperature received from the main sensor. In this case, you need to work on something with the LM75. So, choose the desired temperature. Approximately (to say), we chose TEMP02.
Select " Desired" (Desired) and " Alarming"(Warning) temperature values unanimously agree with our wishes. Please note that we say: “wishes.” You are free to set any values. But the uneducated should rush to extremes and set the values, roughly speaking, around 15 degrees. This will not bring the desired result.
You see exactly, we first have to choose the temperature, over time we can choose its parameters. That's all, you can rename the name of the temperature (using the mouse alias by pressing “F2”). The new name will be more clearly displayed in the main window.
We have renamed TEMP1 and TEMP2 to CPU1 and CPU0.
It turns out that we have finished renaming and setting parameters in (types of each temperature. Since in our case the highest liquidus in the system is the “Case” temperature, we decided to reflect it in no tasks (checkbox " Show In Traybar»).
About this time we must hide in the main window the temperatures that are unused. In our case, these indicators are LM75. Not every system has unused sensors, but it also happens that there are unconnected sensors on the motherboard that report incorrect values (in particular, 127 or something like that).
Uncheck those temperatures that you feel are not useful or have the wrong values.
There is now a way to organize the temperatures displayed in the main window. Until now, what we have to do is drain the drag&drop to move them to the source or down.
So, the first part of the setup was successfully completed, and the authors of these lines achieved the following result:
Fan settings
In the same manner as in the case of temperatures, we can rename the names of the fans...
... turn off unused ones from the main window...
... and organize.
Ordering speeds
These are the default parameters for the interests of this system. You can set home minimums ( Minimum value) and maximum ( Maximum value) power values for each fan.
Don't forget that not every motherboard has internal reserves to control fan speeds. This, first of all, depends on what sensors may be installed on it and detected by the SpeedFan program. In this case, the same applies to temperatures, voltages and fans. Unimportant (= unimportant) each sensor chip can control all these parameters. SpeedFan displays all the information available to it.
(as) as usual, we can rename...
... remove unused ones from the main window (W83782D has 4 PWM, but you are unlikely to use them to this day) ...
... and organize.
We won't discuss voltage settings here. Ant. describe there, because They can also, by analogy with other parameters, be renamed, hidden and arranged.
Assigning speeds to temperatures
Now the main window looks much better than when the program was first launched. The flame icons have disappeared, and unnecessary values no longer clutter the window :)
So we still have CPU0 speed and CPU1 pressure of 100%.
It is necessary to reduce the fan speed.
Please note that you will not be able to change all speeds. This depends on the sensors and controllers installed on your motherboard.
So, in this case, we have the W83782D, we have the ability to change many parameters.
Going again twenty-five to the settings panel, we can see exactly the temperature of CPU0 is associated with all available speeds, two of which have flags, and the other two are conspicuous by their absence. This happens because we hid such speeds from the main window and the program, assuming that we did not need these speeds, unconsciously unchecked them.
Each PWM can raise or lower the speed of one fan.
Speculatively, each fan can affect any temperature.
Then we tell the program that the speed of CPU0 and the speed of CPU1 (which are related to PWM2 and PWM1) both affect the temperature of CPU0. This means that SpeedFan will try to intensify. Ant. slow down both of these fans when the temperature of CPU0 is very high and try to slow them down when the temperature drops.
This is how we formed the CPU0 temperature until now.
But it is unimportant (=unimportant) what actually happens in this system.
At this point, the temperature of CPU0 changes under the influence of the speed (fan) of CPU0 and the heat of CPU1 changes under the influence of the speed of CPU1.
We change the configuration adequately.
There is one more temperature that our sisters would like to control: the "Case" temperature.
This heat changes virtually under the influence of both fans. Yes, you and I can easily tell the program about this.
Automatic speed option
As you can see, when the “ Automatic Fan Speed", agility does not change automatically. Therefore, we return to the “ tab Speeds» settings panel.
We select the fan speed we need and put a tick in the “ Automatically varied» (Automatic recycling). This needs to be done for all coolers whose speeds are planned to be compared automatically.
Now the speeds of the fans we need will change depending on the temperatures we set in the "tab" Temperatures».
By default, SpeedFan can change each speed from up to 100%.
In the main program window, uncheck the “ Automatic Fan Speed» (Automatic fan speed control), SpeedFan will stop mechanically controlling the speeds.
Setting the desired speeds
The fans in our system were quite quiet previously at 65% power ( Minimum Value). This is good because it still runs at 5700 rpm. Another ventilator is noisier. Therefore, the value of its power is good to differ slightly from the first one.
90% power ( Maximum Value) the second cooler is full to cool the central processor to an acceptable temperature. Around 100% the noise level becomes quite high.
With these settings, the program will dynamically change the speed of the first fan from 65 to 100%, and the speed of the second - from 65 to 90%.
Please note that if " Alarming"(Warning) liquidus has been reached, SpeedFan will set the fan speed to 100% in addition to what we have set so far.
Here we describe the basic settings that you need to make for the successful operation of the program.
Loading...