Assembling a satellite dish supral 90 cm problems. Installing a satellite dish on the ground

Installation satellite dish on the ground with your own hands. Spontaneous purchase in 2004 of a used satellite television set of two complete antennas and a computer receiver Skystar-1 set the task of launching this equipment. Go into details self setting I won’t do antennas from scratch, you can read about it on the net. (I received a signal from an unknown satellite only after 1.5 months). So, there were two 90cm antennas Supral.
On the second attempt, one satellite dish was successfully installed on the balcony slab of the 6th floor, where it still stands today.
But I had to tinker with the summer option, I could not immediately answer the question of how to install a satellite dish with my own hands. Installation on the facade of the house was hampered by the presence of a supply network input, just on the south side, which did not allow the antenna to be safely fixed. There was another reason. This would be the first satellite dish in a holiday village. In those days, now no longer, for a certain category of people, the presence of a satellite dish is a symbol of prosperity.

Temporary installation

Therefore, the task was to install the antenna in a secluded place, invisible to outsiders and with the possibility of quick installation / dismantling.
The plot next to the house has almost free space to the south and most importantly is not visible from the road in summer due to thickets of bushes. At first, improvised supports were used, but their non-stationarity did not allow reliable signal reception and quick setup satellite dish.
So, let's install a satellite dish on the ground with our own hands. To install the plate support, we use improvised materials; at the nearest car service, I took axle shaft from a Zhiguli (the official name of the plant is AvtoTaZ). Attached it to the old wheel disk regular pins.
I dug a hole 50 cm deep with my own hands, poured 15 cm of sand for a pillow inside. The sand was compacted and the structure was installed.

The article will be primarily useful for everyone who wants to install and configure equipment for watching satellite channels with their own hands.

Many users prefer satellite TV. This is understandable: cable TV has a limited selection of channels.

Today, widescreen models of Full HD television receivers are designed to display images high definition, one could only dream of such in the era of analog TV.

If you connect digital cable TV, the choice of channels will not be great, and the possibilities of the dish are much wider. If we compare the cost, then the price of a cable receiver is practically no different from a satellite one.

And the owners of private houses and citizens living in the countryside, they simply do not have the opportunity to connect to cable television.

Satellite selection

Even before installing a satellite dish, the consumer will have to choose a satellite. Beginners need to understand this issue in more detail.

Satellite television works as follows. First signals from TV channels arrive at the satellite, from which the signals are sent to subscribers to receiving devices or tuners.

The receivers process the signals, and the encrypted channels are decoded. After that, the signal goes to the TV.

With the help of a satellite, you can watch open or encrypted channels, which can be placed separately on the satellite or included in packages of different operators.

To charge a subscription fee, encoding is performed. Today, users are offered to purchase packages. This is convenient, provided that they are purchased, one payment is provided for viewing a large number of channels at once. In order to receive high quality signals from a particular satellite, the antenna must be tuned.

When the satellites are in close proximity, it is possible to receive a signal simultaneously from them at the same time.

If you want to watch at least 30 channels in Russian for free, then tune the dish to the Yamal 201 satellite. Tricolor TV is very popular among users, and most of the channels are on NTV-Plus and Raduga-TV.

Free channels can be selected on Frocus.net. You can get acquainted with paid packages of satellite TV on sites on the Internet. To avoid interference, it is recommended to mount the dish on the roof of the antenna.

Components for connecting satellite TV

Tuner. The receiving device "decodes" the signal coming from the space satellite, converts it and transmits it to the television receiver.

Plate. It is installed in the direction of the satellite to receive a signal, which is subsequently redirected to the convector.

Head or convector. A device that receives antenna signals. After converting the signal, it is transmitted by the convector to the receiver.

Bracket. Special metal construction for attaching the antenna.

Cable. Connecting link between convector and receiver.

DiSEq. It will be needed when signals from several satellites are received in one tuner at once.

F-ki. Connect cable and other equipment. These are the so-called connecotras.

Cable connecting the receiver and the television receiver. SCART, HDMI and tulips.

What should be considered when choosing equipment?

Choose an antenna D = 90 cm, then it will be possible to receive signals from maximum number satellites. The choice of convector polarization also depends on the choice of satellite.

When two TVs or a TV with a computer are used for satellite TV, you will need to connect two receivers and a convector with two outputs.

The bracket is attached with anchors. The leg should allow you to freely rotate the antenna in different directions. Multifeed will be required when not one, but several convectors are fixed on the antenna.

Do-it-yourself plate installation

The Agsat.com.ua/satdirect service will help you find out where to point the antenna. After indicating on the map the place where the dish will be installed using the flag, select the desired satellite from the column, and the direction indicator will appear.

Installation work begins with mounting the bracket on the wall.

Self-configuring a satellite dish

F-ku is wound on the ends of the cable. Cut the insulation from the TV cable by 1.5 cm, bend the screen braid, cut the foil screen with a 0.9 cm indent from the edge, wind the F-ku.

The cable is connected at one end to the convector and the other end to the receiver.

The next step is to tune the antenna to the satellite. We direct the dish according to the compass, and adjust according to the signal level displayed in the receiver's menu. Having achieved the desired result, tighten the nuts on the plate and secure the cable.

Setting up a satellite TV tuner

In the receiver's menu, you must first select the language and check the firmware version. Set the time, time zone and other settings using the dial.

Display signal level quality information. Tune the antenna, focusing on this window.

After completing the settings, you need to scan the satellite. To open access to channels, insert a satellite operator card.

Photo examples of installing a satellite dish

The main home entertainment in the village is television. However, there is usually not much variety in the available channels in the outback. The way out of the situation is to receive satellite TV programs. Reception satellite channels currently not a problem, you can assemble the kit yourself, or you can buy it ready-made. The undisputed leader among ready-made packages (in terms of quality (quantity) / price) is TRICOLOR. But, if the determining selection criterion is the price and only then the number of “normal” channels, then I recommend considering the possibility of receiving “free” (ie, completely free) satellite channels.

In this case, you can purchase any digital satellite receiver, it is better to take a larger antenna and a regular converter. For example, for two and a half thousand rubles (about 2-2.5 times cheaper than the TRICOLOR set) I purchased:

- antenna SUPRAL (Antenna STV-0.9-1.1 AUM) (90cm)

— digital satellite receiver LUMAX DV-638

— Converter Inverto White Tech IDLP-40SST

- several meters of 75 ohm cable and a pair of F-connectors.

Such kits are usually sold in chain electronics stores “under the heading - for receiving HotBird”. But it's cheaper to buy all this "by weight" from the guys involved in the installation of TRICOLOR.

On such a set in central Russia, you can receive practically any of the satellites “hanging” above us (and not just EUTELSAT W4 with TRICOLOR and NTV plus) and watch free (the abbreviation FTA is adopted) channels transmitted from them.

What can you really see? Unfortunately, it won't work all at once. There is, practically, "ALL!", But it is scattered across the satellites from west to east throughout the sky. In short: I recommend choosing satellites (only the Ku range is considered):

ABS1 (75E - satellite position 75 degrees east longitude) - 28 channels (including NTV, DTV, RBC, Illusion, etc.),

YAMAL 201 (90E) - 15 channels (including NTV, TNT, STS, Ren TV, etc.).

I’ll note right away that the usual ORT and RTR are not here. But, I think, these channels can be caught everywhere on the “wire in the antenna socket of the TV”, the satellite will be an addition to the “wire”.

Briefly, the installation scheme:

The antenna is mounted on the included bracket SKN 600-900. The installation is made with a view to the south, preferably higher (away from people) (photo antenna.JPG). The wind load on the 90cm antenna is quite large, so I fastened the bracket with 8mm “screws” 140mm long (log wall, sheathed with boards). To check the fasteners, it's good to hang on the bracket. (The process of assembling the antenna is well described in the instructions that came with the antenna, so we'll skip it).

The converter is fixed with a regular holder in focus, we pull the cable from it to the receiver.

The receiver is already at home, a cable from the converter is connected to it. The video output is connected to the TV's Video input, and the audio outputs are connected to the Audio input(s) of the same TV.

Features of mounting and installation of the antenna

Only one satellite can be received per antenna and one converter. In general, choose a satellite with open Russian language channels the easiest way is here (http://www.lyngsat.com/freetv/Russia.html). Then, knowing the name of the satellite and its location, we will use the Satellite Antenna Alignment program (http://www.al-soft.com/saa/satinfo-ru.shtml) and for our location (you need to know the coordinates locality, or choose the nearest one from the large database built into the program), we determine the azimuth and elevation angle for the satellite you like, for example, for Vladimir, YAMAL 201 got 125 and 13 degrees, ABS1 got 140 and 19. Next, you need to look out the window at the found angles and make sure that you can see the sky without any interfering objects.

Converter position

A special moment when mounting the antenna is the rotation of the converter in the holder (often this is not mentioned). Let's omit electrodynamics, from practice: the deviation of the position of the polarizer from the calculated one within 10 degrees does not particularly affect the reception quality. Because both satellites are located to the east, then we turn the converter counterclockwise by 27 degrees for Yamal or 21 degrees for ABS1 (the angle between the straight lines in the photo). For other regions, we can advise: if the satellite is from us (we look to the south) to the east, then we turn counterclockwise, if to the west - clockwise, the maximum angle of rotation is 30 degrees (this is when the satellite is almost on the horizon). The mark of the position of the converter for vertical polarization is indicated on its body

Setting the antenna vertical

After installing the antenna mounting bracket on the wall and installing the antenna on it, the fun begins - searching for a satellite. To approach the solution of the problem fully armed, I recommend that you properly set the elevation angle of the antenna (vertical position). To do this, set the plane of the plate strictly vertically (I used a plumb line attached to the upper edge of the plate). After that, draw a line with a marker on the installation node in elevation, passing through the turning point of the dish in the vertical plane (line A on the moving part of the antenna and the same line B on the fixed part in the figure - they coincide in a vertical position). Further, it is convenient to set aside several scratches along the protractor on the fixed part of the mount

Elevation installation

Next, we set the antenna in elevation to the value determined earlier (in our case, 13 degrees Yamal and 19 degrees ABS). We have an offset antenna, the angle of inclination of the focal axis, which relative to the horizon is 26.5 degrees. Therefore, we tilt the antenna “down” by about 13.5 (7.5) degrees (this is between the risks of 15 and 10 (10 and 5) degrees - see photo). It is necessary to set the angle accurately enough, because. the beamwidth of the antenna diagram is approximately 2-3 degrees and a blockage by an extra degree can significantly spoil the signal.

Link to satellite (interfering objects)

It is unlikely that it will be possible to immediately set the antenna in azimuth, so I directed the antenna approximately to the southeast, taking into account the subsequent manual search. Here, when installing the antenna, it is recommended to fix a collar with a shelf on the bracket under it, on which the freely rotating antenna would rest (see the arrow in the photo). This will allow you to freely and smoothly shift the antenna in azimuth when searching for a satellite.

Installing the receiver

The LUMAX DV-638 receiver connected to the TV started working right away. The first step was to test the work on the game "Tetris".

Channel setting for satellite search

Following the satellite search method described in the “Installation” - “Antenna Setup” instructions, I chose the YAMAL 201 satellite (the other one is ABS1) (the list sewn into the receiver’s memory is very large). Type LNB (this is how the converter is called) set UNI1 (there are still UNI2 and UNI3, but we need UNI1). Turned on the power of the LNB - immediately a level of 56% appeared on the "Nutrition" scale. This does not say anything, but it's good that at least the converter responds. Further, everywhere it is proposed to slowly turn the antenna until the maximum value appears on the second “Quality” scale, but this trick did not work for me.

Setting the antenna to the satellite (satellite search)

I caught a satellite in the following way. Select the menu item "Installation" - "Manual search". The satellite has already been selected, guided by the list of channels (Site www.lyngsat.com/yamal201.html (abs1.html)), we set the transponder frequency where the maximum number of channels is transmitted (for Yamal - 11057, for ABS1 - 12640). Polarization - vertical, SR (flow rate) - Yamal = 26470, ABS1 = 22000, other parameters are not important. The entered parameters are enough to track the signal on the "Quality" scale. Next, we slowly turn the dish in the sector where the satellite should be (azimuth 125 (140) degrees - it is more convenient to count from the direction to the SOUTH, then the azimuth is -55 and -40 degrees, I was looking for 20-30 degrees in the sector). The turn must be slow, because. The “antenna beam width” is about 2 degrees and you can easily “skip” the satellite, besides, the receiver’s response time is also not zero. I moved the edge of the dish by 1 cm per second and in about 30 seconds I found a satellite - "Quality" was at the level of 75% for Yamal (it is "louder") and 70% for ABS1. With this quality, automatic scanning shows the presence of far from all channels. It is necessary to “move” the antenna more subtly in the found direction both in azimuth and in elevation in order to achieve maximum “quality”, preferably at a level of 85%, in which case all channels will be found. Tightening the antenna mounting nuts noticeably affects the signal quality, you need to turn them all in turn, controlling the signal.

About the features of the receiver.

After tuning to YAMAL 201, households were happy with the pairs of channels NTV, REN TV, TNT, STS, Domashny, etc. But, a week later, the inscription “Channel is coded” appeared on STS and Domashny. Indeed, the channels were encrypted.

The description of the LUMAX DV638 receiver says that it has an emulator that allows you to view channels with BISS encoding (which is what we need in this case). However, nowhere in the description is there an instruction to enable the emulator. The emulator is turned on by successively pressing the buttons "Exit", "6", "1", "0", "8". After that, the receiver reboots and the "Edit keys" submenu appears in the "Info" menu, if the submenu already exists, then the emulator is turned on. To view STS and Home, this is not enough; it is necessary to register the currently valid keys in the editor. To enable STS and Home on 90E (Yamal 201), I changed the provider name, ID code and key for two cells in the BISS submenu. For STS: ID=0004, Key=C12345296789AB9B; for Home: ID=0006, Key=D12345396789AB9B. After entering the keys (about the ID - most likely they do not need to be entered), closed channels do not open immediately, but after 2-10 seconds they open.

The described alternative to TRICOLOR is quite acceptable. In addition to the broadcast ones, we have (Yamal 201): NTV, TNT, RenTV, STS, Domashny (all in two hour shifts), Channel Vesti, Bibigon, Znanie, etc. And at a much lower price, and even "with your own hands" . In addition, nothing prevents us from “going to a free satellite TV search” and watching one and a half thousand channels on HotBird or Astra, etc. All you need is a wrench and time...

This article will walk you through the installation process. satellite dish, although many consider it rather complicated and troublesome. After all, cable television is already outdated, has many disadvantages, for example, limited list channels and poor picture quality. But the main advantage of satellite is the cost.

If the monthly fee for a cable service is constantly changing, then an average of 160 Ue is enough to purchase equipment and install satellite television. For residents of suburban areas and the remote private sector, this is practically the only opportunity to secure access to a wide range of channels being viewed.

Organization of the system

  • the channeling signal is sent to a specific satellite located in space;
  • each subscriber receives a signal on a dish;
  • it is processed through a tuner or receiver;
  • picture and sound on the TV screen.

To provide satellite TV on your own, first you need to decide on the operator of the services provided or choose the satellite from which the signal will come.
Some satellite TV channels provide an encoded signal, they are included in the subscription package or broadcast separately. This is considered the property of the provider, therefore it requires paid decoding. Companies provide customers with a service in the form of the ability to view a large number of channels from one source. At the same time, Russian channels are served to the consumer with different devices that are located at remote locations. So you will have to choose closely spaced satellites or change the equipment.
Popular satellites that provide signals to a wide range of free channels:

  • YAMAL201;
  • Sirius;
  • Amos;
  • hot bird.

The convenience of choosing the last three is that the reception is carried out from one plate. When combining communications, 37 free Russian channels come out, plus many in foreign languages ​​that do not require additional investments.
When choosing a provider, you should focus on the leaders of the Russian market, these are:

  • Tricolor TV;
  • NTV-Plus;
  • Orion Express (Viva TV).

All operators have official websites to get acquainted with the information, they provide the terms of cooperation and channel packages.

Equipment set

After determining the provider of the services provided or a separate satellite, a complete set of equipment is purchased. It includes:

  • signal receiving antenna;
  • the bracket serves as a means of securing the equipment;
  • the converter receives a signal from the plate;
  • receiver;
  • cable;
  • disek (DiSEq);
  • f-connectors;
  • connection cable.

Purpose and scheme of operation of the kit

The signal goes from the satellite to the dish, which reflects it to the converter. Then it goes to the receivers for satellite TV, where it is processed and converts the signal into a picture on the screen. The converter is connected to the receiver with a television cable. Disek is needed in case of receiving channels from several satellites, it connects the converters into one cable. F-connectors are required for a holistic design, they help to connect the cable to the equipment.

Selection of components

For high-quality signal reception, it is important to purchase the appropriate elements of the kit. There are recommendations for the choice of components.

Special attention to the receiver

Many consumers consider its cost to be the determining factor for the functionality of the device, the price of the receiver ranges from 60 to 600. Inexpensive devices that provide reception of the main channels are popular among consumers. Purchasing a device with a high price is not justified in the case of an ordinary TV, because you can not expect an improvement in image quality. When connecting the above-mentioned Sirius-Amos-Hot Bird satellites, an inexpensive receiver will be enough, in addition, it remains possible to receive a signal from other satellites.
One of the main requirements is the ability to flash, update software allows you to expand the list of received channels. It is desirable that the firmware version be updated, sometimes this gives up to a dozen additional open channels. Manufacturers are constantly releasing new models with an increased number of functions, so there is no point in purchasing expensive equipment. Experts suggest buying receivers from well-known companies, because the production of subsequent products is based on the improvement of released models.
Also pay attention to the presence of output connectors, the main ones are:

  • scart;
  • tulips (to connect to the TV);
  • ANT IN and ANT OUT for additional devices;
  • RS 232 connects tuner to computer;
  • 0/12 V expands the functions of the disc.

The best options for choosing are models of receivers with firmware:

  • GLOBO;
  • Opticum;
  • Star Trask;
  • openbox;
  • sky fly.

It also offers middle-class equipment with the presence of an emulator or a slot for installing a coded channel reception module.

Plate Specifications

By design features plates are divided into:

  • direct focus;
  • offset.

The second option is more common among consumers due to its availability and practical operation.
There is also a division according to the material from which the product is made. A practical, durable and affordable option remains a steel antenna. Also on the market are products made of plastic, aluminum and mesh, but they have many disadvantages.
It is much easier to decide on TV satellite antennas - you need to know the required diameter, it can be 0.6-3m. With a larger diameter, best opportunities signal. As a rule, a plate with a diameter of 90cm is enough. The above providers require:

  • Tricolor TV - 0.9m;
  • NTV-Plus - 0.6m;
  • Orion Express (Viva TV) - 0.9m.

In areas of poor coverage, the installation of plates with a diameter of more than 1.2 m is required.

Converter models

The choice of converter device is reduced to determining its polarization, this is determined by the type of satellite. She happens:

  • linear;
  • circular.

At the same time, there are universal converters, they are designed to work with satellite TV and the Internet. The main indicator of the quality of the device is the noise level. The proposed devices come with a certain number of outputs, that is, if you want to watch programs through a computer and a TV, you will need 2 outputs. When using several converters, you will have to purchase a multifeed.
From inexpensive devices, guaranteed quality is offered by MTI Blue Line devices. They are designed to work with offset antennas, there are many new models with different capabilities.

Satellite TV installation

The main nuance when choosing a satellite is the possibility of receiving a signal from it, which means the absence of obstacles. It is important to point the antenna at the satellite, so if there are buildings or vegetation nearby, you will have to install a satellite dish on the roof of the house. Otherwise, you will have to choose another signal source.
To install the equipment, there is an algorithm of actions:

  • choice of a company providing a service or a direct satellite;
  • selection of equipment;
  • antenna assembly;
  • determining the direction of the satellite;
  • fixing the bracket;
  • installation of satellite dishes;
  • connection of all equipment;
  • setting.

Installing a satellite dish

Before installing the equipment, the antenna itself is assembled, instructions are attached to the device. The video shows the process of assembling the plate in stages.


It is worth paying attention to the antenna mirror, it is quite fragile, especially for aluminum mirrors. Any mechanical damage can change its geometry, respectively, worsen the reception of satellite TV frequencies. After assembly, check the reliability of all fasteners.

Choice of location and direction

When installing a satellite dish, they independently determine the direction where the dish should look. The rules are calculated:

  • position angle - deviation of the line of elevation from the horizontal with direct line of sight to the satellite;
  • azimuth - direction to the satellite.

Calculations are carried out according to complex formulas However, in practice a different principle applies. In the case of setting up a TV for a popular satellite, you can see the direction of the surrounding, already installed equipment. Often when self installation take neighboring plates as a guide.

Bracket mount

First, mark the places for the holes and drill with a puncher. The bracket itself is hung on the anchor, they are reliable and practical. Before installing satellite television, the antenna is tied with a safety rope. The antenna is put on according to the instructions, the mounts are slightly tightened, because you have to adjust the equipment with rotational movements.

Connection

When the plate is installed, the TV cable is started, this requires:

  • installation of connectors;
  • connection to the converter;
  • connection to the receiver;
  • voltage supply.

To install the connectors, the wire insulation is first cut off at the edge, the screen braid is bent in the opposite direction. You also need to cut the foil 0.8 cm from the edge, it isolates the core of the wire, so the connector is screwed on. The process is repeated for the second end of the cable, then one side is connected to the converter, and the other to the receiver. In the presence of several convectors, the wire is connected to the disk, from there there is already a connection to the receiver. After connecting it to the TV, you can supply voltage to the equipment.

Satellite TV or how to set up an antenna

The direction of the antenna can be determined by:

  • compass,
  • special devices.

With the first method it is clear, you need to know the coordinates of the satellite. In the second case, the task is greatly simplified thanks to the Satfinder device, which helps to quickly identify the satellite and tune the antenna to it. There are two types of devices:

  • turnout;
  • automated.

It is clear that the cost of devices is different, the price of the switch starts from 10ue. But the second type of equipment contributes to the completion of the cymbal tuning process in a short time. To accurately determine the required position, the satfinder is connected between the receiver and the antenna. Next, enter the data in the "Antenna Settings" menu for the required satellite and transponder, turn on the power. When changing the horizontal and vertical position of the antenna, the maximum increase in the scale on the left side of the device is achieved. It is these segments that characterize the quality of equipment settings.

Preliminary calculations help to cope with the task; when adjusting, they are guided by the signal level.

Satellite tuning with free channel package

Take for example the setting for the Sirius satellite, the course of action:

  • connecting the receiver to the TV;
  • entering the installation parameters according to the instructions. To do this, select the "Antenna installation" mode in the main menu, in " Manual search” set the frequency to 11.766 GHz, horizontal “H” polarization.
  1. in planes;
  2. towards;
  3. using a converter.

1. For the first point, it is worth rotating the antenna in a horizontal direction, the movements should be smooth. Deviations can differ literally by 1 mm, while the difference in signal quality is significant. In the absence of a signal, you will have to correct the initially set vertical angle of the antenna.
2. To improve the quality of the image, you can move the plate up and down a little, just change its position a little. Otherwise, the image may disappear completely.
3. Turning the converter in the holder along its axis can significantly improve the situation; marks are made on the device for this purpose.
Next, the vertical "V" polarization is adjusted, the actions are similar to the previous process.
With successful tuning, a qualitative level of signal reception is achieved - now it remains to securely fix the reinforcing nuts. Subsequently, you will have to perform such settings for each satellite, however, not by shifting the dish, but by adjusting the converter. Next, open the signal to the encrypted channels by inserting an access card from the operator.

How to set up Tricolor TV yourself

Considering that the most famous satellite digital television in Russia is Tricolor TV, it is worth considering the option of setting it up.
Connection and installation is carried out in the same way as described above. For the initial orientation of the antenna, you need:

  1. turn on the receiver;
  2. in the "Antenna settings" menu, scroll to the right;
  3. wait for the appearance of two bars at the bottom of the screen, showing the strength and quality of the signal, respectively;
  4. further orientation is approximate, already installed plates are viewed;
  5. when a signal appears on the screen, the bars will begin to fill with a green scale;
  6. for adjustment, horizontal and vertical movement of the antenna by several millimeters is used;
  7. 70% of the scale is considered sufficient.

After a high-quality setting, when the receiver is turned on, the subscriber is offered to download the Tricolor TV update, it indicates full list channels. Knowing the data on the set of equipment, you also need to register the receiver. To do this, just fill in the data on the official website of Tricolor TV, after confirming the information, the contract number is issued and the subscriber card is activated. It remains to send the contract in paper form to the company by mail.

Equipment for digital television- this is what you can buy in our store. Our company has been operating in the market of terrestrial and satellite equipment since 2003 and we already know most of our customers by sight.
For regular customers of our online store there is a system of discounts, which is calculated automatically according to the coupon number assigned to you personally.
All equipment passes pre-sale preparation, namely, it is set latest version Software for satellite and terrestrial set-top boxes. All receivers are tested for performance.
Our company delivers equipment, both in Moscow and throughout Russia. Most courier companies have agreements for reduced shipping rates.
In our online store you can find almost any equipment that you may need to receive satellite and terrestrial television. We tried to make the ordering process convenient for anyone. If you plan to order more than one item, but several, then you can use the search in the store and pay attention to related equipment. If you want to pick up equipment for receiving satellite TV, then you should go to the tab menu "Satellite TV", if for receiving terrestrial or cable TV, then " Terrestrial television"etc. If you have any questions during the ordering process, you can use the online chat, which is located on each page of the online store, or order a call back.
We hope that in the digital TV online store you will be able to spend the minimum amount of time ordering the required equipment.



Loading...
Top