This article will cover all aspects related to setting up ASUS routers when connecting to a Rostelecom provider. The points related to the parameters and their connection to the Internet will be described. We will also shed light on all the advantages and disadvantages when choosing routers from this company. An example would be setting up an ASUS RT N12 router for Rostelecom.
Setting up an ASUS RT N12 router for Rostelecom
There are several connectors on the back of the device. Four of them are designed to connect home network other computers and devices, and a fifth is required to connect your service provider's cable. Parameter setting should be performed from a device that has a direct connection in the network card.
Important: when connecting, check the network settings operating system. In the selected section, you will need to set the acquisition of an IP address automatically.
Next, we will deal directly with the installation of the router. There is a sticker on the back panel that contains the IP address, username and key to enter its parameters. To launch the device installation window, you need to enter its address in the browser line. For the company in question, it is the same 192.168.1.1. Next, the router will select the parameters automatically, you just need to fill in a few simple fields. The user will be prompted to change the key to the router settings, then the device will automatically select the type of connection, require a password from the Internet and prompt you to come up with a name and password for your Wi-Fi. This completes the automatic selection of parameters and the Internet should start working. If there is still no Internet, then the information below is especially for you.
Setting the router parameters manually
To perform parameterization manually, select the "Connection" tab and enter the following data:
- WAN connection - PPPoE;
- activate WAN - yes;
- activate NAT - yes;
- enable UPnP - no;
- receive IP automatically - yes;
- automatically connect to DNS - yes;
- enter the login name and key provided by the provider.
The rest of the data should be left as default. If everything is done correctly, then you will already be able to browse the Internet from your computer and other devices connected to the network. If necessary, you can also arrange wireless network.
WiFi setup
In the router interface we find "Wireless networks" - "General" and set:
- hide SSID - no;
- SSID - enter the name of your WiFi networks;
- Wi-Fi network mode - auto;
- channel width 20/40 MHz;
- channel - 7;
- extended channel - auto;
- WPA key - come up with a password for your Wi-Fi network;
- authentication method - WPA-Personal;
- WPA-AES encryption.
After that, save the settings and exit the router interface. Checking the internet connection. Next, consider a number of problems that usually occur when setting the parameters of this device.
Setting up the ASUS RT G32 router for Rostelecom is practically no different from installing the previous one, but there are a few things you should know. If you should select WPA2-Personal. Also, when installing the router itself, you will be prompted to select a port. If there is television from this company, we select the same port.
Configuring ASUS DSL N10, RT N10P and RT N 10U routers for Rostelecom
Since the above three devices belong to the same family, their setup is no different from each other. We connect the wires in the same way as on the RT N12, after which we proceed with the installation. We enter the same IP address in the browser line. And in general, the parameters of these models do not differ much from the previous ones. We will be prompted to set the time zone, select "GMT + 02.00 South Africa, Greece, Ukraine, Romania, Russia, Turkey".
When prompted to select a provider, select Others. In the settings window that opens, set the same configurations as described above. As you can see, setting up ASUS routers for Rostelecom is not particularly difficult, you just need to follow the instructions clearly.
Important: when setting up the ASUS RT N10P router for Rostelecom, you should take into account its not too high data transfer rate. Therefore, if the load on the router is more than 1 device, we recommend purchasing another router.
Possible problems and their solution
If the computer reports that it is not possible to access the Internet, we perform the following steps. It is necessary to set the wireless network settings on the computer to the same ones that you specified when parameterizing the router.
If there is Wi-Fi, but no Internet access, go to the settings and check if there is a connection to Rostelecom. If not, restart your router. If the problem persists, contact your ISP.
Advantages and disadvantages of ASUS routers
The undoubted advantages of the products manufactured by this company can be considered high quality signal without failure, good connection speed, even when connecting three or more devices, ergonomic interface when setting up. Also, almost all models have an excellent design that will successfully fit into the interior of any home.
The downsides are the short cable on most devices and the slightly overpriced price. However, the high price is not set for all models. For example, the ASUS RT N 10U router costs only 500 rubles and is also ideal for setting up a network from a provider such as Rostelecom.
Thus, its main function - high-speed Internet connection of the model of the company in question performs perfectly and their advantages significantly cover the disadvantages.
The Asus RT-N 12 router is a standard device with average characteristics, which should be enough to meet the needs of users. The presented model is compatible with IPTV, but iptv setup on an asus router, it can only be done at the standard level: a port is allocated for this, but traffic is not registered. Wi-Fi is fully supported by 802.11n, which, under ideal conditions, allows you to overclock the Internet to 300 Mbps. But in reality, of course, the speed is several times lower, although this is enough.
So how is Asus? Let's figure it out.
Setting up the router
The IP address on the network for the presented device is the most common - 192.168.1.1. To see the web interface, you need to drive the following into the browser line: http://192.168.1.1. It looks something like this:Figure 1 Interface
The username and password are standard - admin, admin. After the first login, the "Setup Wizard" will be displayed. The tool is useful for beginners, as it allows you to configure the router in simple conditions. After clicking the "Next" button, an attempt will be made to automatically select the connection type. If unsuccessful, the device will give you a choice.
By setting up the asus rt router, L2TP is selected for Beeline, and PPPoE for Rostelecom and other providers of this type. Click "Next".
advanced setup
How to setup wifi router asus rt nt12 on its own without a program?If the default is English language, then change it:
Figure 2. Changing the interface language
Below are the settings for popular Russian providers at the moment.
These include:
- Rostelecom;
- Dom.ru;
- beeline.
Setting up PPPoE for Rostelecom
In the advanced settings section, select the "WAN" subsection:
Figure 3. Select WAN
We use the parameters set in this way:
- WAN type - connections - select PPPoE;
- Receiver digital television(IPTV STB parameter) – select exactly the port where the STB device is connected;
- UPnP - connect;
- Obtain an IP address offline - enable;
- DNS - server - enable offline receiving;
- Login - information indicated on the card or in the agreement concluded with the provider;
- Password - provided by the provider;
VPN L2TP to Beeline
How to configure the Asus RT N12 router to work with Beeline?- WAN - connection - L2TP;
- Port selection - where the device is connected;
- UPnP - enable;
- Automatic WAN acquisition - enable;
- Standalone DNS server - enable;
- Login and password - the latter is issued by the provider, and the login is directly the phone number;
- L2TP server - resource tp.internet.beeline.ru.
Opening the port
In the advanced settings section, go to "WAN" and click on the subsection of the virtual server:
Figure 4 Virtual server
We turn on the "Virtual Server" service, that is, we set "Yes".
Fill in the service name string. Here you need to write the name of the program or application for which, accordingly, the port is opened.
In the "Port range" value, enter the one that opens for the application. The same is indicated in the value of the local port.
In the line of the local IP address, enter the value of the nominal PC for which it will be registered.
Confirm and apply the settings.
Setting up Wi-Fi
Setting up wifi is pretty simple. How to set up correctly? Let's go to the extra section. settings and in the subsection of the wireless type network.
Figure 5. Wi-Fi setup
Step-by-step instructions for setting up the Asus RT N12 lx router to work with a wireless type network:
- "SSID". In this field we write the name (identifier) of the network. It can be absolutely anyone;
- "Verification method". Select the "WPA2-Personal" option;
- "WPA Preshared Key". Enter your Wi-Fi password here. It can be either an alphabetic or a number combination. But the main rule is at least 8 characters.
Reset
How to configure wifi router Asus RT N12 to reset settings? It should be noted that this procedure is optional and is used if the user cannot connect to personal account due to hacking or intentional alteration of identification data.
Figure 6. Reset button
To reset the settings on the asus rt router, it is necessary that the router is connected to power (anything happens).
The button is located inside the case. Above it you can see the inscription, which for Asus means reset (in other models, everything is simpler - Reset).
It is possible to press the button using a toothpick, pen, etc. You need to hold for about 15 seconds. When the WPS button flashes, you can release and wait a couple of minutes for the settings to reset.
Unfortunately, not every problem can be solved by resetting the router, since problems may not be related to the program, but to physical damage, incorrect network settings, and much more.
Video clip with instructions for connecting
The video clearly and step by step tells and shows how the connection to the network is made, what settings are made and other necessary steps.
Hello! We will now configure the Asus RT-N12 + router. Small overview, photos, specifications and reviews about this router you can read (do not forget to leave your feedback, it is very important for us :)). I am sure that this instruction is suitable for other Asus RT-N12 routers different versions, there are a lot of them, I wrote about this in the article at the link above. Why, according to this instruction, it will be possible to configure almost any Asus router. I have on this moment there is only RT-N12 +, so we will torture him. There will be an opportunity, I will definitely write about other models.
Now we will quickly set up our Asus RT-N12 +, tell you how to connect everything, go to settings, configure the Internet, set the name of the Wi-Fi network and change the password. I will give a link to instructions for updating the firmware. In a few minutes you will already be drinking tea and surfing the Internet via Wi-Fi :)
I will not do a review of this router, as I wrote about it in detail on its page (link at the beginning of this article). I’ll just write that the router looks very nice and stylish, works stably, and we intend it mainly for home use. Suitable for connecting tablets, phones, laptops, TVs, etc. via Wi-Fi, and if there is no wireless connection, you can connect 4 devices via cable. For a small apartment, or a small house, this great option.
We will set up according to the scheme:
- Connecting and entering settings
- Setting up Asus RT-N12 using the wizard quick setup
- Setting up an Internet connection with a WAN provider (if it did not work through the quick setup wizard)
- Setting a Wi-Fi password and changing the wireless network name
- Change the password for access to the settings.
To configure the router, we will definitely need information about what type of connection your provider uses and whether it binds to MAC address y. And if the connection type is PPPoE, L2TP, or PPTP, then you will need additional data, such as username, password, possibly IP, etc. All this data is provided by the provider. How to find out the type of connection, i.
Connecting and quick setup Asus RT-N12+
Connect power to the router. If the power indicator does not light up, then check if the power is turned on with the button on the back of the router. Connect a network cable from your ISP or modem to the WAN connector. And in one of the 4 LAN ports, connect the cable, which will connect the router to the computer. If you do not have a computer, or laptop, or no network cable, then you can configure the router via Wi-Fi. But, better by cable, then it can be disconnected from the computer.
If you will configure via Wi-Fi, then just connect your laptop (or another device, you can also set it up from a tablet or phone) to the wireless network that will appear immediately after turning on the router. The network will be called Asus and will not be password protected.
It may be that the default network will be called differently, or will be with a password. Perhaps someone has already tried to set up our Asus RT-N12. I always advise doing a factory reset before setting it up. Press and hold the button on the back for 10 seconds (showed it in the photo above). When released, all indicators will turn off and the router will start to turn on.
We go to the control panel
After everything is connected, open any browser, and type in the address 192.168.1.1 . Settings should open right away. If this does not happen, or something went wrong with you, then take a look. We should see the quick setup wizard. To start, press the button Go.
On the next page we need in the field Network name (SSID) specify the name of your Wi-Fi network, and in the field network key set a password to connect to this network. Write this password down somewhere.
The router will think and reboot. A Wi-Fi network will appear with the name we just set. Connect to it already with the new password we just set.
After connecting, return to the settings again. A window with connection information should appear. Click Further.
The router will ask you for a username and password to access the settings. (which you set during setup).
If everything is exactly as I described above, then you are very lucky. This most likely means that your ISP uses connection technology Automatic IP, and the router configured everything itself. By the way, the Internet through the router should already work. This completes the router setup.
But, if you have a connection type L2TP, PPPoE, or PPTP (providers: Beeline, Dom.ru and others), then the setup will go a little differently. You will just need to manually set some parameters.
Internet setup PPPoE, L2TP, PPTP (Dom.ru, Beeline) on Asus RT-N12
If your provider uses PPPoE, PPTP, L2TP, or Static IP technology, then after starting the quick setup wizard, after checking the connection, the router should prompt you to select the type of your connection.
You may need to specify some more parameters. IP address, service name, etc. It all depends on the type of connection, and your provider.
During the setup process, as soon as the router establishes an Internet connection, it will prompt you to set up a Wi-Fi network, etc. Perform these settings as I showed above in this article.
You can always yourself change WAN settings(internet connections). Just go to the main settings page (there is a button in the quick setup wizard), and open the tab Internet - Connection.
On this page, you can always set the most important Internet connection settings. If the Internet through the router is already working, you have changed the wireless network name and password, then you can finish setting up the Asus router. And I'll show you where and how you can change the most important settings.
Wi-Fi setup and password change
If you want to change the name of your Wi-Fi network, or change the key that you use to connect to Wi-Fi, then you can do this at any time in the router settings directly on home page. Simply enter a new username and/or password and click the Apply button.
More wireless network settings, including channel settings can be found on the tab Wireless network(left).
After changing the network name or password, don't forget to reconnect your devices to Wi-Fi. If you have connection problems (usually after a password change), delete your network and reconnect to it.
Asus RT-N12 router settings protection
During the setup process, we have already set New Password to access the control panel. But, if you have not done this, or want to change your password, then go to the tab Administration - System. Enter the same password twice, and click the button Will apply b.
Now, to log into the admin panel, you will use this password. Don't forget it :) On this page, you can also change the time zone, assign an action to the WPS button, enable Telnet, etc.
If you have read this article to the end and you still have a desire to do something, then you can update the firmware of your RT-N12. There is a lot on this topic.
In this article, we will consider detailed information on setting up the Asus RT-N12 router. But so that you do not make a mistake with the choice of a router, then Here you can find detailed specifications, photos, comments, and various reviews.
In the instructions below, we can quickly cope with all the work ahead of us. You will be able to find out how to connect it correctly initially, get to its settings item, select the Internet configuration correctly, rename wifi router, assign your own password. Also, a link will be presented a little lower, if you go through it, you can get to the firmware update site. IN general work takes a little time, in a few minutes you will have your own Internet distribution center, which will be ready for use.
The characteristics and reviews of this router were presented above, but it is worth highlighting that such a router looks very elegant and even very attractive. What needs to be said about the work is that it works flawlessly and will always give you access to the internet. Such an Internet distribution center is ideal for home use, as it will give you the opportunity to connect all your devices to the Internet in your home. However, it happens that the devices are not connected, then you can connect 4 devices via cable at once.
We will configure Asus RT-N12 according to the scheme:
- Turning on the power and selecting the "Configurations" item
- Selecting the correct configuration of the Internet distribution center through the window for automatic configuration.
- In case of failure using the previous paragraph, we will consider the settings manually
- Managing the basic settings of the router - name and password
Before proceeding with the configuration, we need to configure the router, but for this we need information about the connection types of your provider. All this he must tell you which one your provider uses. And also about how it passes your data through the MAC address. If your ISP names types like PPPoE, L2TP, or PPTP, then you'll need even more details. For example: username, IP address, password, etc.
Power supply and configuration item in Asus RT-N12+
First, power up the Internet distribution center. At correct connection The light should come on to indicate power is on. If nothing lights up and does not blink, then check what word the button on the router is on - on or off. Then you need to connect a cable from the provider or from your modem to the WAN connector. Then you need to connect a cable to connect your computer via the LAN connector. However, there are users who do not have a single device that has a LAN connector, and if you are one of these people, you can also configure via Wi-Fi, but this is undesirable. After setting up via a LAN cable, you will not need it and you can stick it out as unnecessary.
In the second option, in which you cannot connect via LAN wire, you will need to connect your device via a wireless Wi-Fi network. To do this, just turn on the router, and then connect the wireless network in your device. She will be called Asus and she will not have any password.
With desperate attempts, it still doesn’t work, then view article on connecting a laptop to Wi-Fi .
Sometimes it happens that someone before you has already chosen the configuration of your router. Then at the same time your router will have some other name and some password. In such cases, it is recommended that after connecting the router, immediately reset all settings. To do this, just hold the button on the back of the router for 10 seconds. The picture of this button was presented in the photo above. After 10 seconds, all the lights will stop burning, and the router will reboot and everything will turn on again.
We go to the control panel Asus RT-N12
After successfully connecting your device to a network called Asus or wired Internet network, you will need to open any of your browsers and type this address 192.168.1.1. After loading the address, you should see your configurations, but there are times when this does not happen. It will be enough for you to view this. The photo below shows the configuration window. In the first step, you will need to click the " Accept". If you're having trouble logging in, read the general article about logging in and troubleshooting -
Step by step you are given a choice for a password in order to protect all your data and configurations in the Asus router. This item is required. “Drive in” the password 2 times, remember, and for greater security, write it down. As suggested, press the button " Further».
Once accepted, your router will turn off and then turn on again. After that, it can be found in the list of all available networks with its new name. Now you need to connect to your named router and the password-protected router.
After connecting, return back to the previous setup site. You should now see a window with detailed information about your router. Now click " Further»
You should "fall out" a window asking you to enter the username, as well as his password. You specified all this at the very beginning of the setup.
That's all. This type of setting is suitable for people whose connection type is " Automatic IP". If so, then the router configured everything itself. Now you can use the Internet.
If your provider uses a different type of connection (It was described above), then your setup will look a little different than the one described above.
Setting up other connection types
Some ISPs do not use automatic IP connection technology and use PPPoE, PPTP, L2TP, or Static IP. Then you need, after updating the connection data, specify your connection option. (You can get it from your ISP).
Next, a window will pop up asking for a username and password. This information can be obtained from the contract concluded on the Internet connection, as well as from the provider. It is enough to call him and find out this information.
But this is if one of the types that require only this data is selected. There are types that require an IP address, a service name, and the like.
You need to remember that you are the commander of all settings! You can choose your own settings depending on your needs. wan. To do this, just go to the initial settings window and select Internet connection.
On the boot page, you can choose the configuration of settings you need at any time. If you followed all the points and did not miss anything, then everything should work for you. If so, then you can now safely use your wireless connection. The following will provide information on how to change frequently changed configurations in the router.
How to change the network name and set up Wi-Fi yourself
If your friend wants to change the name of your network, as well as the password presented to it, then you can do this right on the settings boot page through the configuration window. It is enough to enter new variables and click the "Apply" button.
To select, as well as edit, even more configurations, you need to click the item " Wireless network»
When you have changed the network name and password, reconnect your device. If the attempts are in vain, it will be enough for you to remove the network from the Known list, and then reconnect to it.
Security of all router settings
When hacked or if you want to change the password and user name in the security of the router, go to the tab " Administrator", Further " System". Then you can edit all the data you need and Apply their.
After the change, you will use the data you specified to log in to the system.
Loading...