Wifi works d link. Configuring the WiFi router D-Link dir300 ("gray" interface)

D LINK DIR 300 router, WAN and LAN connectors. WAN - Internet input, LAN - local area network

Many users are frightened by the need to configure the d link dir 300 router on their own. However, there is nothing wrong with this, in fact. It is impossible to break it without significant efforts, and if you make any mistakes in setting up, you can always start from scratch. At the same time, only attentiveness and patience are important, which will be required if you are doing this for the first time and have not previously entered the router settings.

Overview of the design and its connection

The first difficulty that users face is the need to abstract from understanding the physical device as such and its virtual ones, more precisely, software settings. Therefore, we first consider the design of the router d, which, depending on the year of manufacture, may differ slightly.

Important!When choosing a place to connect and install the router, make sure that there is a power outlet in close proximity to it, as well as a provider cable that is inserted into the port with a connector.WAN located next to a group of four LAN ports that are similar in appearance.

First, the device is connected to a household power outlet, then to the provider's network, and only then, using a patch cord (the cord that comes with the kit) to a computer or laptop, if the dir router will be configured with their help. Either end of this cord plugs into any of the four LAN ports, while the other end plugs into a laptop's network jack or power network map computer. If the setting will be used wireless device- a home tablet or smartphone, then it will not be needed at all.

patch cord is a patch cord, cable

Advice! If the standard 1.5 meter patch cord is not suitable for convenient operation with a computer, it can be replaced with another one purchased separately from a computer electronics store or radio market.

The remaining three ports for local connection LAN can be used for other wired connections after setup. For example, you can connect:

Multimedia receiver for TV;
Second PC for shaping home network;
External disk for arranging cloud storage.

On this physical connection router ends, and the setting wifi router d link dir 300 can start.

Windows users

At the next stage, when the d-link is physically connected, the system will automatically download the necessary drivers and detect it without unnecessary manipulation by the user. However, when working with OS Windows versions 7–10, you need to optimize the system parameters for correct operation.

This will require launching the Control Panel, which is accessible from the Start menu. In the list of categories, you should find "Network and Internet", and after its launch, select "Network Control Center". In the dialog, you will need to find an element called "Change adapter settings" and select in context menu for it the "Properties" element.

In the next window, select the "TCP / IPv4" element and also select the "Properties" item for it. This will allow you to choose for it the choice of DNS server addresses and IP in automatic mode.

Main job

The next step in configuring the router will require launching any browser, for example, Chrome or Moilla Firefox, and in the input line where the site name is usually entered, you need to write the email address indicated on the sticker stuck with reverse side dir 300 router.

browser address bar, paste 192.168.0.1 or 192.168.1.1.

Most often these are the numbers 192.168.0.1 and 192.168.1.1. In addition to them, the login (admin) and the corresponding password (admin) are often indicated, which are standard in this case. They should be entered when prompted on the page and press "Enter". Next, an interface with a list of configurable parameters will be automatically loaded.

Enter login and password

choose language

To do this, the following items are selected in the list in turn:

System.
Administrator password.

On this tab, enter the name (you can leave "admin") and New Password and then click the "Save" button.

At the next stage, go to another section, choosing one by one:

Net.
Compound.

Go to advanced settings

Now you need to delve into the contract received from the provider and find out in it the type of connection that is used. Most often this is IPoE or PPPoE, although other options are possible. The required one should be selected from the list and, if the MAC address is used, enter it in the corresponding field. You will also need to set marks on the items:

Obtain a DNS address automatically.
Obtain an IP address automatically.

Creating and configuring a wireless connection

To set up a Wi-Fi connection, you will need to select the following items in sequence:

WiFi.
Basic settings.

First, you need to check the box "Enable wireless connection". IN open tab you must enter a new network name in the "SSID" cell and select a region from the drop-down list to obtain national standards. To save the settings, you need to click the "Change" element.

Further, it is recommended to immediately set or change the default password. It is necessary so that unauthorized people cannot access your network resources and devices connected to them. To do this, go to the "Security Settings" item. The list of its parameters includes the Network Authentication field, which should be set to the WPA2-PSK type. As a result, the list of parameters will change and in the field "Encryption Key PSK" you will need to enter a password that you have invented, and for the WPA field corresponding to encryption, you should select the type TKIP.

When finished, click the "Change" button for the adjustments to take effect.

This completes the basic configuration of the d link dir 300 router, and to correctly complete and save the parameters, select the "System" item located at the top right, and in the open dialog click the "Save and Restart" button.

Resetting the settings to the initial state

If you cannot enter the settings, most likely, someone has previously configured the device and changed the protection settings. In this case, as in many others, for example, if a new, malfunctioning firmware has been installed, resetting the settings will help. It is also called a rollback, which is easy to do without going into the device settings.

To do this, the design of the dir model provides for a physical “Reset” button. To avoid unexpected failures, it must be pressed and held for 15 seconds.

Note!Excessive force when pressing a key« Reset" will not give the desired result. On the contrary, it can cause physical damage, since the button is soldered directly to the board.

After the manipulation is carried out, all data about user settings, including passwords and network addresses, will be destroyed. Therefore, in order to avoid the painful selection of values for all parameters, it is advisable to save the configuration in a settings file on the computer.

Additional parameters and options

It is worth noting that, in addition to its main functions, it has several modes of operation. This is an access point for distributing wi-fi, a bridge and a client. At the same time, the model has a considerable number of auxiliary options. For example, it can be used to set up the reception of IP TV channels, and, if necessary, restrict access to a specific list network resources which is especially important when working in an office.

The design features of the model allow you to easily understand how correctly the device works. The front panel is equipped with LEDs that signal the operation:

power supply;
Internet connections;
local wired connections;
wireless connections.

For example, a green glow indicates readiness for work, and a yellow one indicates possible problems. In this case, green blinking corresponds to data transmission on the corresponding channel. But the physical WPS button also has a blue flashing mode, which indicates an attempt to establish a connection.

There are a lot of similar features and you can learn more about them from the instructions included in the package. In case of problems, you can also contact hotline provider.

Eventually

Now you know that anyone can install routers and it is not necessary to call a specialized specialist to set it up. You can do it yourself, and after not a long practice, you will be able to master more complex options available in new firmware, which can be downloaded from the official website if you have an Internet connection.

You can connect the DIR-320 router to the Internet using an external modem or a regular Internet cable provided by your ISP. All parameters are specified in the web interface; no separate application is required to configure the router. D-Link devices have a large number of settings that allow you to achieve optimal home networking.

Connecting the DIR-320 router and entering the web interface

You can configure the router with a wired or Wi-Fi connection. Insert the Internet cable into the router, which was brought into the room by the provider. To do this, use the last port marked in gray. Connect home computers using the LAN ports highlighted in blue on the rear panel.

Insert the plug of the power supply into the “5V-2A” connector. If the Internet will be connected via an external 2G/3G modem, insert it into the USB port. The DIR-320 should only be plugged into an outlet after all cables and external devices have been connected. Otherwise, interruptions in the operation of the router or its breakdown may occur.

Connect the network on the computer from which the settings will be changed D-Link router DIR-320. At using Wi-Fi select "D-Link" from the list of wireless connections. By default, there is no encryption, so you can complete the operation without entering a password. If you are using a cable connection, insert the plug into the Ethernet port of your computer or laptop.

On the selected device, open a web browser, for example Google Chrome. In the address bar of the program, enter the IP that will be used to access the settings of the DIR-320 router. Address in standard firmware router: 192.168.0.1. On the page that opens, you will need to enter data to access the control panel. Standard login and password: "admin". Fill in the text fields and click "Login".

Note! If the account on the D-Link DIR-320 was changed earlier, reset the router settings. To do this, press and hold the Reset button on the rear panel for 10 seconds. When the factory settings are restored, log in again with the default data.

If you enter your account information correctly, you will be redirected to the statistics page. Among other data, it displays the total number random access memory on the DIR-320 router and the amount of available memory. Below is the time since the last power on of the D-Link router.

Internet connection via 2G/3G modem

To establish a connection via external device, go to the "Internet Settings" menu and in the first field check the value " USB Adapter". Select your carrier's name from the following drop-down list. If there is no data for your 2G or 3G provider in the system, set the value to " ' and write the operator's name in the following text field.

In the "Username" and "Password" sections, enter the data provided by the provider. If necessary, enter the dial-up number in the corresponding field and the name of the access point in the "APN" line. Specify necessary information possible in technical support or on the official website of the Internet provider. The remaining items are recommended to be left unchanged.

Open the "USB modem -> Information" section. In the first list, specify the type of modem depending on the generation used wireless communication. Allow access to mobile Internet in the second dropdown list. The remaining rows of the table will contain information about the connected device. Click the "Connect" button in the lower right corner of the page.

Important! If the modem is not recognized, disconnect it, then re-insert it into the USB port and click the Refresh button below the table.

Some operators require you to enter a PIN to connect to mobile internet. You can specify this information in the same menu, through the "PIN" section. Enter the current numeric password provided by the operator in the "PIN code" field. To prevent the system from asking for a code every time you connect, check the box and click "Apply".

Cable connection DIR-320 to the Internet

Open the "Network" menu and go to the " P-t-p interfaces". By default, their list will be empty. To create new interface for D-Link, click the "Add" link in the connection table. In this section, you can create network connection using L2TP, PPTP and PPPoE protocols.

Select a connection type from the first list. It can be clarified in the contract that was concluded with the Internet provider. The account information is also indicated there, if they are required to establish a connection. In the absence of an agreement, you can clarify the data by calling or writing to the support of the company that provides Internet connection services. Fill in the required fields and click "Edit".

Connection with a static IP is made in a similar way. When you select "Static" in the "Interface Type" section, new text fields appear: IP address, netmask, MAC address. All this data is also provided by the provider.

The "Status -> Network Statistics" section contains information about the operation of various interfaces, including:

Designated addresses;
The speed of receiving and returning;
The number of received and sent packets;
Dropped packets;
Packets received with errors.

Setting network parameters

You can manage running interfaces in the "Network -> Network interfaces" section. Next to each entry, the current state of the connection is displayed. Each of them can be temporarily stopped or disabled. Among available interfaces- connected LAN devices (laptops, computers and other home network devices), Wi-Fi and WiMAX wireless technologies.

To add DNS servers, go to the "Name servers" section. In the "Setting method" field, by default, automatic receipt of values from the Internet provider is set. Selecting "Manual" will allow you to specify other DNS servers. You will be able to enter their IP addresses in the second text box. Click "Change" to save the addresses.

Assignment of IP addresses within local network performed by the DHCP server. Open the " Configuring DHCP” to change its mode of operation. In the "Static DHCP" table, you can bind permanent addresses for individual devices. The match is based on the MAC address.

You can find out the MAC address of the device for further binding in its parameters. For computers running an operating system windows definition MAC is produced in command line. To do this, use the command: "ipconfig / all".

The settings of the current server can be changed by clicking on its name. Most important parameters in this table, the start and end address of the range. The system will automatically assign new clients IP addresses from this numerical range. If you need to change it, make sure that the new values are within the range allocated for local networks.

Tutorial Video: D-link DIR-320 Step by Step Setup for Dummies

WiFi setup

Open the "Network -> Wireless" tab. The first flag is for Wi-Fi operation module. If you remove it, the wireless broadcast of the router will be terminated. Other options:

Hide access point - makes the network invisible in the general list.
SSID - Wi-Fi name that will be displayed when searching for networks.
Country - allows you to select the territory in which the device is used. The parameter affects the list of allowed channels.
Channel - band number within the Wi-Fi frequency. Default value: 6.
To select the type of encryption and specify the Wi-Fi access key, click Security Settings.

In the first list, select a network authentication method. By default, the connection to D-Link is unencrypted and no password is required to connect to Wi-Fi. It is recommended not to leave the value "Open" in order to avoid interception network traffic. Select a different authentication type and set the PSK key (the password that will be used for Wi-Fi).

Important video: D LINK dir 320 router settings

Changing the system settings of the router

On the "System" tab, you can reboot the D-Link router or go to any subsection. If the reboot is performed by clicking the button in the Actions table, the changes made in the previous steps will not be applied. To save them, another button is used: "Save and reload". It is located in the upper right corner.

The "Administrator Password" section allows you to change the data of a standard account. To do this, select the "admin" user and check the "Change system password" box. Enter the new password and its confirmation in the next two text fields. To provide the best protection home network, use complex passwords, containing special characters, numbers, small and large letters.

When all the necessary settings WiFi router D-Link DIR-320 will be changed, it is recommended to save the configuration to a file. Go to the menu item "System -> Configuration", click " Backup copy» and select the directory where the backup will be written. If the router crashes or another user accidentally restores the factory configuration, you can restore the settings from the saved file.

Advice! To restore the factory settings, use the corresponding item in the same menu.

D-Link recommends updating regularly software router. Each new firmware contains not only the expansion of functionality, but also updates network security. Usage latest version The software will protect your device from hacker attacks. The current version can be downloaded on the manufacturer's website, in the "Support -> FTP" section.

The downloaded file is installed on the DIR-320 via the "System -> Software Update" menu. Click the "Browse" button and specify the path in the system where the new firmware is saved. Then click "Update" in the lower right corner. The update installation process will take several minutes. After the router automatically reboots, you can use new version software.

In order to start configuring the D-Link DIR-300 router, open the box, boldly tear off the orange sticker from the router. You can forget about the sticker.

We connect the router to the computer with a wire (blue patch cord) supplied in the kit.

First, open a browser Internet Explorer, Firefox) and type 192.168.0.1 in the address bar.

Connecting wirelessly to a router may not always be successful, because in addition to your router, others may be available, it is possible to connect and configure someone else's D-Link DIR-300 router.

Login: admin

Password:(we leave the field empty, although out of habit I want to enter admin)

On the "Installation" tab, select the "Internet Setup" tab, and then the "Manually configure Internet connection" button.

Looking ahead, I will say that the address in the local network of the provider can be issued dynamically or be static, usually at the request of the user. For a static address, providers usually ask for an additional subscription fee. There are two options D-Link DIR-300 router settings, depending on what type of receiving addresses in your case, I personally use a static address, it's more convenient.

Configuring a D-Link DIR-300 router with dynamic IP address assignment.

Option D-Link DIR-300 router settings No. 1, if the address is obtained via DHCP, i.e. dynamically.

In the "Internet connection type" field, select "PPTP Dual Access" (namely, dual access, I don't know the fundamental difference, but you need to do it this way).

1. Choose a connection with dynamic address assignment by the "Dynamic IP address" provider.

2. MAC address - if there is a binding on the provider's network MAC address, click Clone MAC address, while router D-Link DIR-300 copy the MAC address from network adapter your computer, relevant in cases where the router was not purchased at the time of connection to the provider.

3. IP address/server name - IP/server name of the provider.

4. Account PPTP - username for authorization in the provider's network.

6. Re-entering the PPTP password - we repeat the password for authorization in the provider's network.

7. Select connection mode - connection establishment mode. In the figure, "Always-on" is selected for a permanent connection. "Connect-on-Demand" - establishing a connection if necessary - that is, when there is traffic directed to the Internet, the router establishes a connection, and if there is no activity for more than the time specified in "Maximum Idle Time" - it disconnects. If "Manual" is selected, the connection is established and terminated manually.

8. Save changes to

Configuring a D-Link DIR-300 router with a static IP address assignment.

1. Select a connection with a static address value "Static IP address".

2. IP-address - the address given to you by the provider.

3. Subnet mask.

4. Provider gateway.

5. DNS - provider's DNS Server.

6. MAC address - if the provider's network has a binding to the MAC address, click MAC address cloning, while the router will copy the poppy from the network adapter of your computer, relevant in cases where the router was not purchased at the time of connection to the provider.

7. IP address/Server name - IP/Server name of the provider.

8. PPTP account - username for authorization in the provider's network.

10. Re-entering the PPTP password - repeat the password for authorization in the provider's network.

11. Select connection mode - connection establishment mode. In the figure, "Always-on" is selected for a permanent connection. "Connect-on-Demand" - establishing a connection if necessary - that is, when there is traffic directed to the Internet, the router establishes a connection, and if there is no activity for more than the time specified in "Maximum Idle Time" - it disconnects. If "Manual" is selected, the connection is established and terminated manually.

12. Save changes to D-Link DIR-300 router settings by pressing the "Save Settings" button.

After the correct settings, the connection router D-Link DIR-300 with the Internet must be installed, as indicated by the "Internet Online" indicator on the left side of the browser screen.

The D-Link DIR-320 router is considered one of the most popular ones. It is not uncommon for a person to buy a D Link router, bring it home, and then call the Internet provider and say: “Here, I bought it and I can’t set it up.” Consider briefly specifications and appearance.

Appearance and characteristics

As for the characteristics, there is little that can be said, because all routers are extremely similar. The wireless network standard is 802.1g/b. On a Wi-Fi router, in addition to LAN ports, there are 1 USB port. The antennas on the modem are removable. To be more precise, it has only one antenna. The device itself supports PPPoE, L2TP, PPTP connection protocols.

On the front of the device there are various indicators, light bulbs that allow you to monitor the status of certain characteristics:

First comes the standard power indicator, showing whether the router is turned on.
Next come the indicators showing the status of the Internet, the Wi-Fi wireless network.
After there are 4 indicators of local ports. They show if there is any router connection via LAN cable, and if so, through which port.
The last USB indicator that shows if the USB port is enabled.

There are various ports and connectors on the back of the machine where you can insert cords and cables to correct installation:

First, there is one antenna, which allows communication to reach further around the house or apartment.
Then comes one USB connector, it has a green stroke.
Then there are 4 blue local ports, they are required to connect using a LAN cable.
Then one WAN or INTERNET connector for connecting the Internet to our modem.
The penultimate connector is needed to connect the power supply.
The last button is labeled "RESET". It is needed to reset the settings, it is used to reset the password. The button itself is located inside the hole, which protects it from accidental pressing, because after resetting the password, the router has to be reconfigured.

Router Installation

Before you configure anything, the modem needs to be unpacked and installed in a place convenient for us. It is important that there is an outlet nearby, so that the Internet cable gets there, so that there is a PC nearby.

There is nothing complicated in the installation. For proper installation, you just need to connect electricity to the router, connect the computer and the Internet through the cords. The internet cable is provided by the internet company. At this stage, the configuration and installation of D Link DNS to the required location is over.

Complete router setup

Before you start setting up the Internet and wireless network, before setting up the D Link DIR 320 router, we need to check if the computer is connected to the modem correctly.

Connection test

To check the connection of a computer that is running on operating system Windows 7, we need to go to "Start", then to the standard computer control panel. (It's easier to do as in the instructions for the screenshots, it will help you set up the D Link DIR 320).

Now we need to select "View network status and tasks".

After we have selected the required item, we need to click "Change adapter settings".

Now you need to look in the properties of "Local Area Connections".

We need to see if the Internet Protocol version 4 properties are correct.

Here we put ticks, if they are not there, everything is opposite auto tuning like in the screenshot. And click "OK".

In the event that you have Windows 10 on your PC, then follow a different instruction. "Start", and then you need to click on "Settings".

Click on the "Network and Internet" sub-item.

On the left in the menu, you need to click on Ethernet, then we look at setting the adapter parameters, as in the first instruction.

Now we also look at the properties of the LAN network.

We look at the properties for the fourth version.

Again, set the automatic configurations and click "OK".

Now we are sure that the connection is working properly, if not, then we update the software. And on the updated router, you can now perform some actions.

Setting up an Internet connection

To perform any further actions, we need to enter the router settings. This happens through the browser, there we go to 192.168.0.1 or 192.168.1.1 - these are sites. This must be done on a PC that does not have an internet connection.

In the window that opens, we are prompted to enter Login & Password. By default, the username and password are identical - admin.

Now we have entered the center of all configurations, we need to change the interface language to Russian, so that it is easier. In the upper right corner, where Language, select "Russian".

PPoE

Consider default setting over PPPoE. The last is the type of connection, you need to check it with the provider. All important information for setting may be in the contract. So the first thing to do is look there.

In the "Network" block, click on WAN. In the window that was just opened, you need to click "add". Here we do as shown in the screenshot.

You need to select the connection type PPPoE, or the one that is prescribed by the Internet company in your contract.

Then we indicate the username and password, they are numbered 2 and 3.4. This data is in the contract with the Internet company.

After that, click "Apply". Internet should now appear on your computer.

PPTP with dynamic address

First, to perform debugging, we need to go to the WAN link, which is located in the "Network" block. On the new page, click "Add".

1. Type of connection, as in the name of this subparagraph, PPTP with a dynamic address.

3. Next, we need to provide a username and password. This data must be provided by the provider.

4. Same with the VPN server. It must be provided by the provider.

5. Click apply.

PPTP with static address

In order to configure a static connection, you need to add a new connection. This must be done in the WAN window, it is located in the "Network" block. We select the connection type that we need - PPTP + static.

1. After you need to fill in the fields in the IP paragraph. All required fields must be completed. And we can request data from the provider, support services, or find it in paper contracts.

2. Now the settings of the VPN item. Immediately check the box next to automatic settings. After we register all the selected fields. This is the username and password twice, they must be in the contract. As well as the address of the VPN server.

3. Click apply.

Setting up a wireless network

Setting up Wi-Fi is even easier. To do this, in the Wi-Fi block, select the basic settings (if you can’t find it, then first you need to click on the advanced settings at the bottom of the page).

After you need to check the box next to "enable wireless connection." Then we provide the required information. SSID is the name of your Wi-Fi. Here we write any, only in English letters. Click "Apply".

Now you need to set a password for Wi-Fi. To password-protect Wi-Fi, select "Security Settings".

In the "network authentication" field, select WPA2-PSK. The encryption key, which is number 2, is the WiFi password. After the new password has been entered, we need to save. To do this, click on "Save and reload", this is at number 3.

Now all the questions about how the router is configured D Link Dir 320 nru should fall away. Sometimes, before setting up a router, we need to learn how to flash a D Link Dir 320 router. But we will talk about this, and how to create a network storage using a D-Link DIR router, in another article.

Change factory password

In field Enter a new password - Enter a new password.
In field Repeat the entered password - repeat new password.
Then press the button Apply.

After that, the router will prompt you to re-enter its settings.

Internet connection setup

We go to " Net» ⇒« WAN". If you already have connections created here, we recommend deleting them. To do this, tick them and click the " Delete".

After that click on the button Add.

Setting up a PPPoE connection

In field Connection type: select PPPoE
In field Interface choose Internet
Allow WAN Direction- must be checked
Username: Your login from the contract
Password: Your contract password
Password confirmation: repeat password
Service name - you can leave it blank.
Authentication algorithm: Auto
keep alive . Spacing and Dips- you can leave the existing values.
MTU
In field Miscellaneous NAT And Firewall.
If the provider provides Internet TV service, check the box Enable IGMP.
Click Apply.

Setting up an L2TP connection

In field Connection type: select L2TP + Dynamic IP
In field Interface choose Internet
In the Name field, enter a name for the connection. You can leave the current value
Allow WAN Direction: must be checked
: must be checked
In field IP make sure the checkboxes are checked NAT, Enable IGMP And Firewall
Username: Your login from the contract
Password: Your contract password
Password confirmation: repeat password
VPN server address:
Authentication algorithm: Auto
keep alive- check the box for permanent connection
MTU- change the value to 1450 or less
In field Miscellaneous make sure the checkboxes are checked NAT And Firewall.
Click " Save».

Setting up PPtP (VPN) when automatically obtaining a local IP address (DHCP)

In field Connection Type: select PPTP+ Dynamic IP
In field Interface choose Internet
In the Name field, enter a name for the connection. You can leave the current value
Allow WAN Direction: must be checked
Obtain DNS Server Address Automatically: must be checked
In field IP make sure the checkboxes are checked NAT, Enable IGMP And Firewall
Username: Your login from the contract
Password: Your contract password
Password confirmation: repeat password
VPN server address: write down the address of the provider's VPN server
Authentication algorithm: Auto
keep alive- check the box for permanent connection
MTU- change the value to 1450 or less
In field Miscellaneous make sure the checkboxes are checked NAT And Firewall.
Click " Save».

Setting up Wi-Fi on the router

1. Go to the tab WiFi, select the item " basic settings» and set the desired wireless access point name SSID. The remaining parameters are left as is (see picture). After that, press " Apply».

2. WiFi, select the item " Security Settings". Select Authorization type(recommended WPA2/PSK) and then to the PSK Encryption Key enter any password of at least 8 characters - this will help protect your wireless network from unauthorized access. Save your changes. WPA encryption - AES. After that click Apply.

That's all: now you can try to use the Internet by wireless wifi connection from a laptop, tablet or any other equipment.

Setting up IPTV

Option 1. Select a port for the set-top box without specifying the VLAN ID

Thus configured digital television Beeline, Dom.Ru, TTK and some branches of Rostelecom. This method is the simplest. Select a section from the menu Start - Master IPTV settings . In the window that opens, click on the port to which the TV set-top box will be connected - it will be marked in green. As a rule, the 4th LAN port is used for this. Click on the button " Save". Now you can connect the set-top box to the 4th LAN port.

Option 2. With an explicit identifier virtual network VLAN ID

This method is used when multicast traffic is delivered to a subscriber device in a separate virtual network and is divided directly into terminal equipment. According to this principle, the service is organized in many branches of Rostelecom, Tattelecom. In this case, to configure the port, you need to go to the section Additionally - VLAN. Here we click on the group LAN” and wait until its parameters open.

Once in the group settings, select the port in which the set-top box will be turned on and uncheck it (in our example, we unchecked 3 LAN ports). We click on the button Save and we go back to the section VLAN.

Now you need to click on the button Add". This will create a new group.

In the "Name" field, write the name of the group - IPTV, for example.
Check the "Allow" checkbox.
In the "Type" list, select "Transparent".
In the Vlan ID field, you must specify the identifier of the virtual network. My house uses 1601. Keep in mind that identifiers are used differently on each optical ring and you can only find out which one is used on your home switch in the provider's technical support.
We put a daw "Multicast".
The rest is left by default.
Note only the moment that in the "Untagged ports" list, the port that you removed from the "LAN" group should be checked.

Port Forwarding/Forwarding

We go to Firewall - Virtual servers . We press the button Add.

Name- enter any name.
Interface- choose the interface that is responsible for connecting to the Internet. In our case, this is the pppoe interface.
Protocol- choose the protocol you need.
External port start\end, Internal port start\end - enter the range of ports you want to open.
Internal IP- IP address of the device to which requests will be sent
Click Apply.

Checking the Internet Connection Status

Go to Status - Network statistics. In the plate, the Internet connection you created should be green and all columns in this row should be filled.

Saving/restoring router settings

1. Choose to save the current configuration. To save the current settings of the router, the settings file will be saved to the specified location on the hard drive.

2. To restore settings from a file, you must click and select Loading a previously saved configuration to the device, specify the path to the file with settings, then click the button.

3. To reset the settings to factory settings, press Factory settings.