Before you set up Tricolor TV on your TV, you must carefully read the instructions for installation and internal settings. Only a well-performed installation will avoid the appearance of any difficulties during use. Installing the system is quite laborious, but allows you to save on the services of a master. If you first study step by step instructions, then there will be no problems during the installation and synchronization of equipment. You should also study the settings in advance so that the receiver works correctly.
First you need to independently fix the antenna on the outer wall of the house and adjust the mirrors to the satellite. To do this, you need to pay attention to the following points:
- Choice of installation location. The dish should be fixed in such a way that it is located on the side of the satellite, which is located on the equator and is located in the south. Please note that there should be no obstacles between the satellite and the antenna. Even small trees can create significant interference.
- Distance between equipment. The closer the tuner and antenna are, the clearer the system will work. In this case, setting up the receiver will be much easier.
- Correct installation. When assembling the antenna, keep in mind that the converter must be installed with the holder up. This eliminates the possibility of a negative impact of precipitation on the functioning of the system, protecting the "heads" from bad weather.
- Reliable connection. The converter should be connected to the cable using a special F-connector. This eliminates the possibility of malfunctions during operation. The cable must be insulated no more than 10 mm. The connector must be twisted as much as possible.
Antenna adjustment process
The more precisely the dish is adjusted from the side of the geographical position, the better the signal can be achieved at the output. The peculiarity of this procedure lies in two criteria: elevation and azimuth. These values are measured in degrees.
Please note that in the process of regulation there are difficulties that are associated with the fact that, in accordance with the region where the equipment is installed, the indicators may differ and this is considered the norm.
For example, in Bryansk, the angle = 29 degrees, and the azimuth = 178 degrees. This feature should not be overlooked. Specify the standard characteristics of mono on the official website of Tricolor TV.
Setting up Tricolor TV on a Samsung Smart TV
In order to properly configure the equipment, you must first familiarize yourself with the process.
In this case, the model of the tuner, the size of the antenna, the quality of the equipment for synchronization, as well as the model of the TV are of great importance.
How to set up Tricolor TV yourself if the settings on Samsung Smart TV? If any interference or ripples appear, pay attention to the correct installation of the system. Measures must also be taken in the absence of channels that have previously been broadcast.
To do this, debug the received signal level as follows:
- Enter the system menu in the "Signal level" section and find the "Settings" option.
- Enter the password (default value is 0000) and confirm the actions to be performed.
- Go to " System settings” and click on the “OK” button.
- Select "Antenna settings" and select the list of channels, in accordance with the region of use: EUTEL SAT 36V or 36 A.
- Find 2 scales that indicate signal strength. They must be filled up to 70%. In this case, the work was carried out correctly, and no changes need to be made. In this case, attention should be paid to mechanical damage and adverse factors.
After completing the above steps, you can proceed to more fine tuning systems. Please note that the receiver must be registered if this procedure was not carried out during the conclusion of the contract. Otherwise, the equipment will not function.
Set up Tricolor TV by yourself video
ATTENTION! If your receiver does not find channels, then the setup instructions
Current (latest) software version from 07/06/2016
ATTENTION!
Never turn off the power of the TV until the update is complete! Otherwise, it may fail!
Return previous version Software will be impossible!
Software update via satellite
To update software via satellite, the TV must be connected to a configured satellite dish.
PROCEDURE:
To start the update, turn on the Telemaster service.
Attention! If the service is not displayed in the general list of channels, you need to search for channels again. After a few seconds, a message will appear stating that the module software needs to be updated ( appearance the messages shown in the instructions may differ from the messages displayed by your receiving device):
When this message appears, confirm the start of the update.
If you refuse to update, you will be prompted to perform it again after rebooting the receiving equipment. You can install new software at any time convenient for you.
After confirming the start of the update, messages will be displayed on the screen informing you about the update process:
After the update is completed, the module will automatically restart. If this does not happen, you can reset the module manually by turning off the receiving equipment from the power supply and turning it on again. You can also remove the module from the CI+ slot and reinstall it.
Tsareva Larisa 17763
Nowadays, it is not at all necessary to purchase a separate tuner for the TV. Many modern TV models already have built-in receivers and special slots for CAM modules. All you need is to choose the desired operator, buy a module and a smart card from him, and enjoy the selected channels. The Tricolor TV CAM module is one of the most popular. Perhaps users most often choose this operator because of the favorable ratio of prices and quality of services. Not everyone knows how to connect and configure the Tricolor TV cam access module, so detailed instructions will be given below.
What is needed to connect the Tricolor TV CAM module?
To watch what you want paid channels through an access card, you need to purchase:
- satellite dish;
- RG-6 cable that connects satellite dish with TV;
- Circular polarization converter;
- Conditional access module CAM Tricolor TV;
- Tricolor TV smart card (it is offered with the module and an annual subscription, in the future you can buy the card separately).
 |
compyou.ru | 12 320 Р | |
 |
|||
 |
|||
 |
|||
 |
|||
| More offers | |||
How to connect and set up?
First you need to tune the satellite dish to the broadcast frequency with which the Tricolor TV operator works. To do this, you need to set the parameters "Eutelsat W4 / W7 36.0`E". Connect the antenna with a cable through the F-connectors to the TV plug marked "SATTELITE".
For high-quality antenna tuning, it is better to call a specialist, but you can do it yourself if you are familiar with such matters. When everything is ready with the satellite dish, we proceed to configure the Tricolor TV CAM access module itself. Here all the manipulations will already be associated with the TV.
 |
|||
 |
|||
 |
|||
 |
|||
 |
Uni-sat Access module "Tricolor TV" CI+ without card (red) | uni-sat.ru | 1 600 R |
 |
|||
| More offers | |||
- Following the elementary instructions, insert the smart card into the module cell until it stops:
- Then install the module itself with the card into the TV slot (the TV must be turned off from the network!);
- Through the remote control, reset all TV settings by setting them to default (press the "menu" > "support" > "self-diagnosis" > "reset" button, finish with the "ok" button and the TV goes into reboot);
- When the reboot is completed, press "menu" > "channel" > "antenna" > "satellite" again.
- Next, we get into the "satellite system" submenu, after which we press "ok";
- Immediately, a window will pop up asking you for a PIN code, don't be scared, just enter "0000" and the system will show you the entire list of available satellites. Uncheck all boxes except Eutelsat W4/W7 36E. If the checkboxes are inactive, turn off the TV, remove the module, and then do the same again.
- Once in "satellite selection" just click on Eutelsat W4/W7 36E. At this point, you will need to set the following settings for the LNB:
top gen. LNB-10750,
Lower gen. LNB - 0,
Transponder - 12226 H.
- Then go to the menu manual setting" and find the value "Transponder - 12226 H", then click on "search";
The photo of the settings was taken from a Samsung TV, but on other models the menu does not have significant differences, and all settings are made in the same way. if you want to watch satellite digital television from your tablet or smartphone,
Many are faced with the problem of setting up a ci-module with the Tricolor TV operator on Samsung and LG TVs. To do this is quite simple. First you need to decide on the brand company that is the manufacturer of your TV.
Setting up the Tricolor ci-module on a Samsung TV
Setting up the ci-module Tricolor on Samsung TV carried out using the remote control standard menu TV.
- To begin with, we carry out a simple manipulation, go to the "support" menu, then "self-diagnosis and "reset". Enter your pin and reset.
- The next step, go to the settings of satellite channels, we see installed satellite, click on the satellite selection line, on its name.
- We create our own satellite with the name "User sattelite 1", tick and save.
- Go to the broadcast menu and "manually" change by clicking create.
- We write the approximate transmission rate, example "25500" and the frequency "16945".
- Press the network search, it will run through all available transponders, press "ok".
- Insert a module with an access card and "voila" all channels show.
Setting up the Tricolor ci-module on an LG TV.
Simplicity and quick setup ci-module Tricolor on LG TV will take no more than three minutes.
- We put our TV into the satellite channel tuning mode.
- In the settings submenu, select the "Manual settings" item.
- Set the network parameters from the first part of the article.
- We start the search for channels, follow the instructions.
- At the end of the search process, we save the list of channels and understand that we have configured the module.
Many manufacturers of popular brands note that often correct setting similar to other TV models and requires very little time and effort.
tell friends
A standard set of equipment for access to satellite television includes a television set itself, a satellite dish and a receiver that ensures their connection. However, it is quite possible to do without the last device if you purchase a TV with a CI (CAM) module. This module, in fact, performs the functions of a built-in receiver, but at the same time it can be reconfigured, at the request of the subscriber, to any operator, including Tricolor TV. Setting up the ci module for the Tricolor satellite can be done by the subscriber independently, without the involvement of the company's technicians. We'll tell you how to do it.
General information for all subscribers
With the help of the CI module, the subscriber can view both TV programs in standard quality and HD channels. To gain access to broadcasting, it is necessary that the equipment installed in the house meets the minimum standard requirements imposed by the operator.
equipment requirements
TVs equipped with a CAM module can only work with Tricolor content if the subscriber's antenna is set to Eutelsat satellite W4 (currently called Eutelsat 36A/36B). In this case, you won’t have to set any special Tricolor TV tuning frequencies for the ci module on the receiver - the devices will find the signal automatically.
In addition to the requirements for the satellite, there is one more nuance - the user's television receiver must be equipped with satellite tuner, which receives a signal in DVB-S2 format. It is also desirable that the TV has support for 4K UHD and HEVC. This will make it possible to view channels from Ultra HD packages on it.
Important! In the absence of support for these formats, even channels from standard packages may not be available.
Well, besides this, to access the broadcast, you will have to purchase a smart card from the operator and connect it to the equipment. When the installation is completed, you can proceed to the settings.
Instructions for TVs of different models
The procedure for carrying out adjustment operations will depend on the model of the television receiver. In detail and with illustrations, all the setup steps are usually described in the instructions for specific device. We will only provide general information.
Important! Subscribers who have already tried to set the module parameters and have not received a result are recommended to roll back the TV settings to the factory settings before any repeated operations.
After installing the CAM module in the appropriate port, you need to go to the TV settings and set the following parameters there:
- antenna - satellite;
- converter - single;
- satellite - Eutelsat 36A/36B;
- converter power – on (then set “LNB”);
- transponder frequency - 12226.
Then you should save the settings and check the signal quality. For normal operation it should be at least 80%. If the signal level is insufficient, it is worth checking the connection of the receiver with the antenna and, if necessary, reconfiguring the latter.
Next, go to the menu item "Channel settings" and set it auto mode. After the device detects and displays the list of found TV channels, it will need to be saved.
Then go to the "Sound Options" item and set it to MPEG4 mode. This is necessary so that during broadcasting the sound does not hiccup and goes in sync with the image. And the final stage is the transition to the menu section "CI Data" and a rollback to the factory settings.
Next, the receiver is turned off for 5-10 minutes, then turned on again, transferred to one of the coded channels and left for several hours. This is required for the device to receive activation keys from the satellite.
Important! Receiving activation commands should also end with setting up the Tricolor ci module on a Samsung, Sony, Philips TV and other models.
Instructions for Samsung TVs
Owners of Samsung TV receivers should also go to the device menu and select the “Satellite Channel Settings” section. The active satellite will already be marked in it. The mark must be removed, and then ticked at the very end of the list of signal sources, in the line "User Sat1". This is necessary so that the device receives a signal from the Tricolor operator. Setting up the ci module on a Samsung TV continues by setting the LNB parameters in the corresponding section of the main menu. Here it is necessary to set the value of the lower frequency limit to the same as the upper one.
The next section of the menu for setting parameters is “Broadcasting”. It needs:
- go to the sub-item "Channel settings";
- select manual mode;
- find the installed satellite User Sat1;
- click in the line "Transponder" on the word "Create";
- set operating frequencies and transmission speed;
- save settings.
Next, you need to click "Search", evaluate the signal level and start the search again. The equipment must find at least 6 TV channels. To connect the rest of the content, you need to go back to the "Transponder" section, turn on the network search and click the "Search" button again. As a result, the module will find all available channels and make the interface for using television available to the subscriber.
Setting up the Tricolor ci module on a Sony TV
To access broadcasting on Sony TVs, you must follow the following algorithm:
- select the “Settings” item in the device menu;
- go to the "Digital configuration" subsection;
- select the line "Auto-tuning satellite";
- in the "Antenna configuration" window, set "Fixed antenna or DiSEqC";
- leave the default settings in the scan window;
- in the next window, turn on satellite number 1.
Next, the LNB configuration is installed. The upper and lower frequency ranges are set in accordance with the antenna model (the values \u200b\u200bare written in the instructions or directly on the converter case). Now you can return to the list of satellites and click the "Start" button located below it. After that, the module will automatically start searching for available TV channels. At the end of it, it remains only to save the list of found content.
Setting up the ci Tricolor module on a Philips TV
Philips currently does not have an agreement with Tricolor on the implementation of their parameters in the TV software. Therefore, during auto-search, the CI module of this equipment sees all the frequencies of the working satellite, including programs not only of Tricolor, but also of NTV +. To access the desired operator, you will need to do the following:
- go to the menu item "Installation", then "Search for satellite";
- click "Reinstall channels", then "Start";
- wait for the signal scales to be displayed on the screen;
Engineers in various industries are constantly trying to introduce new and improve existing technologies. Not a single industry is left without development, which positively affects the standard of living of all people. This also includes satellite television. A few years ago, CI modules did not exist.
Device Features
Quite often, an important point in connecting television in this way is the presence of a built-in receiver. The presence of a pre-installed device greatly simplifies use, because there is no need to make an additional purchase and install equipment. This is the first thing you should pay attention to when the question arises of how to set up HD satellite television.
Also, it is worth noting that the cam-module should be selected relative to the required encoding. Relatively satellite television Tricolor module needed latest version format "DRECrypt. This approach can guarantee a comfortable enjoyment of HD TV.
Installation and setup
Setting up the Tricolor satellite TV cam module does not take much time. Installation order this device as follows:
- The cam module must be installed in the CI + port with a thick side. The TV must be turned off.
- The installed Tricolor module can show two situations after switching on. First - everything is installed correctly and information about the module and access card is visible on the TV. The second - during installation, an error was made due to which, instead of information, there is only the inscription "error 17". In this case, you need to double-check the correctness of the installation and register on the website of the satellite television operator.
- Next, you need to specify the type of antenna - "satellite" and the required satellite - Eutelsat 36A / 36B. Converter type should be selected "single". Converter power supply to on mode and select LNB Transponder purity can be set to 12226 MHz. After that, you should check the quality of the signal and broadcast.
- If everything works fine, you can proceed to the search for channels. In the menu item "channel settings" you need to select the automatic mode, because in this way the entire search will take place automatically. An important factor here is the firmware version of the TV software. The later version, the more correct the search will be and more channels will be found.
- After a successful search, you need to start setting up the sound of the channels. To do this, go to the "Digital TV Sound Settings" section and select the only suitable MPEG option. Only in this mode, the sound will not disappear while watching TV.
- You should go to the menu item "CI data" and in the settings select the option reset to factory settings. After that, you need to completely turn off the TV.
- After this procedure, you need to turn on the TV and leave it to work until all the necessary HD channels appear. This will happen gradually and may take from 2 to 8 hours.
After correctly performed manipulations, broadcasts in HD format are available for viewing, and the settings of the cam module of the Tricolor television are completed. Also, you should remember about the features of LG TVs. Enabled in the settings menu automatic update and channel search, unlike Samsung devices. This mode can harm the order of the configured TV channel list, as resets may occur. For ease of use this function it is recommended to switch to off mode. Read also
Loading...